BI Fct digital output, Inverting digital Outputs | Siemens 440

Issue 10/06

6 Commissioning

P0731=52.C

P0748 = 0

BI: Fct digital output 1

52.3

Defines the source for digital output 1.

NOTE

The brake relay can also be controlled from another digital output (if this is available) or using a distributed I/O module. Analog to DOUT 1, it should be guaranteed that the I/Os are controlled by the status bit “MHB active”.

Inverting digital	0
outputs

This parameter allows the signals to be output to be inverted.

Frequent settings:

52.0	Ready to power-up	0	Closed
52.1	Ready	0	Closed
52.2	Drive operational	0	Closed
52.3	Fault present	0	Closed
52.4	OFF2 active (present)	1	Closed
52.5	OFF3 active (present)	1	Closed
52.6	Power-on inhibit active (present)	0	Closed
52.7	Alarm active (present)	0	Closed
52.8	Deviation, setpoint/actual value	1	Closed
52.9	PZD / PLC control	0	Closed
52.A	Maximum frequency reached	0	Closed
52.B	Alarm: Motor current limit	1	Closed
52.C	Motor holding brake active	0	Closed
52.D	Motor overload	1	Closed
52.E	Motor dir. of rotation, clockwise	0	Closed
52.F	Frequency inverter overload	1	Closed
53.0	DC brake active	0	Closed
53.1	Actual freq. f_act > P2167 (f_off)	0	Closed

:

:

	DOUT channel			Invert DOUTs
				0 ... 7
				P0748 (0)
			BI: Fct. of DOUT 1
	Function		P0731.C	0
	Function	rxxxx.y	(52:3)
	xxxx.y	rxxxx.y	(52:3)	1	-1
	xxxx.y	P0731 = xxxx.y		1	-1
		P0731 = xxxx.y

Relay :

Text

	CO/BO: State DOUTs	int. 24 V
	CO/BO: State DOUTs	max. 100 mA
	r0747	max. 100 mA
	r0747		Kl.9
	r0747.0		Kl.9
	r0747.0
		COM	Kl.20
		NO	Kl.19
		NC	or
		NC	Kl.18

P1216 = ...

P1217 = ...

DC 30 V / 5 A		Kl.28

AC 250 V / 2 A

-max. opening / closing time 5 / 10 ms

Holding brake release delay (entered in s)

1.0 s

Defines the time interval during which the frequency inverter runs with the min. frequency p1080 after magnetizing, before the ramp-up starts.

P1216 ≥ brake opening time + relay opening time

Holding time after ramp-down (entered in s)

1.0 s

Defines time for which inverter runs at minimum frequency (p1080) after ramping down. P1217 ≥ brake closing time + relay closing time

MICROMASTER 440	57
Operating Instructions (Compact)

Image 57

Siemens 440 BI Fct digital output, Inverting digital Outputs, Holding brake release delay entered in s

Contents

User Documentation Operating Instructions Compact Issue 10/06 Issue 10/06 Contents Contents Issue 10/06 Frame Drilling Dimensions Tightening Torque Size Mounting dimensionsClearance distances for mounting Bolts Input voltage range Technical Specifications Tightening torques for Power terminals Lbf.in Weight Lbs 12,5Order No 6SE6440 26,5 Output Power KVA Weight LbsWeight 1BA1 5BA1 2AD23 2AD24 Power terminals Lbf.in2AD27 2AD31 Input Cable, max Mm2 For UL specified Input Cable, min Mm2Output Cable, min Mm2 Output Cable, max Mm2 4/0 or 300 or 400 or 500 or 1/0 2/0 95 or 150 or 185 or 240 or350 or 4/0 Recommended Fuse 5CA1 Order No 6SE6440 2UE17 2UE21 2UE22 2UE24 2UE25 2UE27 2UE31 Frame Size a Power Terminals Removing front covers Frame Sizes B and C Frame Sizes B and C Removing front covers Frame Sizes D and E Frame Sizes D and E Removing front covers Frame Size F Frame Size F Removing front covers Frame Sizes FX and GX Frame Sizes FX and GX Connection terminals for Frame Sizes a F Connection overview for Frame Size FX Connection overview for Frame Size GX Control terminals Terminal Designation FunctionControl terminals of Micromaster Frame sizes Block diagramTo F FX and GX Pre-assignment of the inputs 50/60 Hz DIP switchInput/Output Parameter Function PC frequency inverter connecting set Establishing communicationsAOP at the BOP link AOP at the COM link AOP as control unit Bus interface CBParameter / Terminal AOP on BOP link AOP on COM link DeviceNet CANopen Buttons and their Functions Step Result on the display Quick commissioning Selection of command source Rated motor powerRated motor voltage Rated motor current Min. frequency Selection of frequency setpointMax. frequency Ramp-up time End of the quick commissioning/drive setting Control modeSelection of torque setpoint Select motor data identification Motor data identification Factory setting Ambient motor temperature entered in CMagnetizing current Select motor data identification with P1910 = Quick commissioning routine Motor data identification routineDetermining the magnetizing current Selection of command source Commissioning the applicationSerial Interface USS Digital input DIN Function digital input Possible SettingsFunction digital input Debounce time for digital inputs Digital outputs Dout Common Settings ClosedBI Function of digital output CO/BO State of digital outputs Common settings BI Disable additional setpointSelection of frequency setpoint Example P1000 = Analog input ADC Analog output DAC Setpoint memory of the MOP Motor potentiometer MOPInhibit negative MOP setpoints Setpoint of the MOP Fixed frequency FF JOG frequency right 10 JOGJOG frequency left JOG ramp-up time Ramp function generator RFG Reference/limit frequencies Delay, fan shutdown Inverter temperature warningInverter protection Motor protection Alarm threshold, motor overtemperature Motor temperature sensorInverter temperature reaction Motor overload factor % Encoder 16 V/f control Continuous boost entered in %Acceleration boost entered in % Programmable V/f freq Coord Starting boost entered in %Programmable. V/f volt .0 Hz Programmable V/f freq .0 Hz Limitations Field-orientated control Sensorless vector control Slvc 17.1 P1750 = Operation directly after an on commandControl word of motor model Zero crossing Vector control with encoder VC 17.2Filter time for act. speed Gain speed controller Supplementary torque setpoint Frequent settingsP1511= CI Supplementary torque setpoint Converter-specific Functions Flying startAutomatic restart Holding brake enable Holding brakeMotor size Brake type Opening time ms Closing time ms BI Fct digital output Holding brake release delay entered in sInverting digital Outputs Holding time after ramp-down entered in s P1230 = P1232 = P1233 = DC brakeBI Enabling the DC brake DC braking current entered in % Compound braking DC braking start frequency entered in HzCompound braking current entered in % Dynamic braking 18.7Vdc controller Load torque monitoring P2182 PID controller Controller structures Parameter Parameter text ExampleP2264 CI PID feedback PID cancer control Parameter Parameter text Setting Meaning Positioning down ramp Free function blocks FFB Enable FFBsP2800 = P2801 = P2802 = Activate FFBs Input parameters Output parameters Setting parameters Data sets Command data set CDS P0820 = P0821 = Drive data set DDSDrive data set DDS bit BI DDS bit DIN Diagnostic parameters CO Actual frequency CO/BO Control wordCO Act. output current limit CO Act. output voltage CO Selected frequency setpoint R1079R1114 R1170 CO Freq. setpoint after dir. ctrl Parameter reset of factory setting Factory resetSeries commissioning LED status display Displays and messages Fault messages and Alarm messages Fault SignificanceAlarm Significance Regional Contacts Online Service & SupportCentral Technical Support Internet Address