Manuals / StarTech.com / Computer Equipment / Server

StarTech.com ECS0016 manual Groups

Models: ECS0016

1 140

Download 140 pages 33.13 Kb

Page 45

Instruction Manual

4.Enter a UPS Name and Description (optional) and the select if the UPS will be Connected Via USB or over pre-configured serial port or via HTTP/HTTPS over the preconfigured network Host connection

5.Enter the UPS login details. This Username and Password is used by slaves of this UPS (i.e. other computers that are drawing power through this UPS) to connect to the console server to monitor the UPS status and shut themselves down when battery power is low. Monitoring will typically be performed using the upsmon client running on the slave server. See section 8.5.4 for details on setting up upsmon on slave servers powered by the UPS

Note: These login credentials are not related the Users and access

privileges you will have configured in Serial & Networks: Users &

Groups

6.If you have multiple UPSes and require them to be shut down in a specific order, specify the Shutdown Order for this UPS. This is a whole

38

Image 45

StarTech.com ECS0016 manual Groups

Contents

ECS0016 FCC Compliance Statement Table of Contents Serial Port and Network Host Configuration Alerts and Logging 105 132 Features Package ContentsIntroduction Initial Configuration Power ConnectionAC power socket 192.168.0.1 Management Console ConnectionClick Start Run ARPPing IP Address AssignmentPage Select System Administration Administrator PasswordOn the System IP menu Network IP addressSystem Services Telnet HttpsBase PingMetaConnect Communications SoftwarePuTTY SSHTerm Serial Port and Network Host ConfigurationConfiguring Serial Ports Common Settings Console Server Mode Page SSH RFC2217 TCPPower Strip Mode SDT ModeTerminal Server Mode Accumulation PeriodSerial Bridging Mode SyslogLocal Ethernet LAN ECS0016 Add / Edit Users Page Authentication Authentication ConfigurationSelect Serial & Network Users & Groups Network Hosts Trusted Networks Select Serial & Network Trusted NetworksNetwork IP Address Subnet Mask Click Apply Serial Port CascadingPage # ssh remhost To define and configure a SlavePlease note Page RPC Connection Remote Power Control RPCPage RPC Status RPC AlertsUser Power Management Managed UPS Connections Uninterruptible Power Supply Control UPSClick Add UPS Groups Configure UPS Powering the Console Server Page Monitor managedups@192.168.0.1 1 username password slave Configuring Powered Computers to Monitor a Managed UPSUPS Status UPS AlertsOverview of Network UPS Tools NUT Page Environmental Monitoring Connecting the EMD Click Add Alerts & Logging Alerts Environmental AlertsEnvironmental Status OoB Dial-In access Failover and Out-of-Band Dial AccessCheck the Enable Dial In Access box Configure Dial In PPPSelect PAP, CHAP, MSCHAPv2 or None and click Apply Using The MetaConnect client Set up Windows XP/ 2003 clientSet up earlier Windows clients Set up Linux clients Page Telnet or SSH connection to serially attached devices Secure Tunneling & MetaConnectNetwork MetaConnect for OoB Connection to the Gateway To configure MetaConnect for OoB accessPoff networkconnection Pon networkconnectionMetaConnect Public Key Authentication To make the OoB connection using MetaConnectImporting and exporting preferences PuTTYgen OpenSSH OpenSSH Windows Setting up MetaConnect for Remote Desktop accessSet up MetaConnect Serial Ports on ECS0016 SSH port forward over the ECS0016 Serial Port Enable SMTP, Snmp and/or Nagios Alerts and LoggingEmail alerts Snmp alerts Configure AlertsSelect Alerts & Logging Snmp Nagios AlertsPage Serial Port Logging Remote Log StoragePower Control Page Configuring Ipmi Power Management Configuring Serial Port Power StripsUser Power Management Configuring Browser Controlled Power StripsNagios overview Nagios IntegrationCentral management and setting up MetaConnect for Nagios Central Nagios serverDistributed ECS0016 console servers MetaConnect Nagios setup involves the following steps Set Up a Central Nagios ServerClients Central Site Remote Site Nagios Server Set up distributed ECS0016 console serversNetwork Managed HostsCheck Prefer NRPE, Nrpe Enabled and Nrpe Command Arguments Click New Check and select Check TCP. Select Port HostSelect Serial Port from the Serial & Network menu Click Console Server Mode, and select Logging LevelClick Connection Alert Enable Nagios on the ECS0016Enable Nrpe monitoring Select System Nagios and check Nsca Enabled Enable Nsca monitoringConfigure selected Serial Ports for Nagios monitoring Configure selected Network Hosts for Nagios monitoringConfigure the upstream Nagios monitoring host System Management System Administration and ResetFirmware Firmware UpgradesSelect the Enable NTP checkbox on the Network Time Protocol Configure Date and TimePort Access and Active Users Select Status Port AccessStatus Reports Support Reports StatisticsSyslog Select Manage Power Power ManagementManagement Device ManagementSelect Manage Terminal Serial Port Terminal ConnectionPort Log Management Basic Configuration Linux CommandsPower up the ECS0016 and connect the terminal device Linux Command lineConfig Tool Syntax Run all registered configurators. ThisDescription Administration Configuration Date and Time Configuration Manually Change Clock SettingsNetwork Time Protocol Network Configuration IP Configuration DhcpTime Zone Disable Dhcp IP Configuration StaticDefault Gateway Secondary DNS# /bin/config --run=dial-in Dial-in ConfigurationServices Configuration Serial Port Configuration Telnet Access LAN Disabled Supported Protocol ConfigurationSSH Access LAN Enabled Raw TCP via LAN DisabledTrusted Networks Config.users.totalPassword secret Event Logging ConfigurationRemote Serial Port Log Storage Username cifsuserAlert Configuration # /bin/config --run=eventlogMetaConnect host TCP Ports MetaConnect Host ConfigurationPmshell Commands Advanced ConfigurationAdvanced Portmanager PmshellPmusers Pmchat# pmusers Portmanager DaemonExternal Scripts and Alerts Signals109 Raw Access to Serial Ports Access to Serial PortsAccessing the Console Port Standard IP-Filter configuration Enabling Boot Messages on the ConsoleEtc/config/ipfilter IP FilteringCustomizing the IP-Filter Etc/config/filter-customEtc/config/snmpd.conf Modifying Snmp ConfigurationTo set the Manager Address field Adding more than one Snmp serverPowerMan Power Strip ControlSynopsis Target Specification Pmpower Adding new RPC devices Speedbaud rate/speed charsizecharacter size/charsize Term Meaning Glossary of Terms UsedChap Intranet InternetMAC address Key lifetimesNet mask NATRouter RadiusTCP/IP address SOLUTP TelnetMicrel KS8695P controller Technical SpecificationsRJ45 Connector PinoutWiring 131 Limitation of Liability Technical Support Warranty Information