Troubleshooting, Replace the PU235N/245N | Toshiba T2N guide

6 F 3 B 0 3 6 2

8.5Troubleshooting

1.If the Ethernet Port fails to come up normally (i.e., does not reach standby state.)

If the Ethernet Port is functional, then the Ethernet Port can be initialized and brought to the standby state (with the ERUN LED lit) by applying power or by issuing a reset request.

	START
		No

	Is power supplied to the T2N power		Apply the rated line voltage to the primary side of
	supply module?		the power supply module.
	Yes
	Yes
	Is the T2N correctly mounted in the	No
	Is the T2N correctly mounted in the	No	Insert the PU235N/245N into its slot correctly.
	base unit?		Insert the PU235N/245N into its slot correctly.
	base unit?
	Yes

Replace the PU235N/245N.

Read out the down information, and send both that information and the PU235N/245N to Toshiba.

2.If the Ethernet Port fails during operation

Recovery procedure

Replace the PU235N/245N.

Before replacing the PU235N/245N, read out the down information, and then send both that information and the PU235N/245N to Toshiba.

3.If a SEND or RECV instruction fails complete

Recovery procedure

(1)Verify that the inputs of function block are held in the on state until the instruction completes.

(2)Determine whether the user program is writing to the status register while the instruction is executing.

⎯ 148 ⎯

Image 149

Toshiba T2N Troubleshooting, If the Ethernet Port fails during operation, If a Send or Recv instruction fails complete

Contents

T2N Ethernet Port Important Information Concerning Important Points Safety Precautions 3 B 0 3 6 Safety Precautions ∙ Precautions for operation ∙ Mounting in the base unit ∙ Connecting to the network ∙ Installation environment and base unit mounting ∙ Basic points in laying out a network ∙ Maintenance ∙ Support for 10BASE-T network Usage Recommendations∙ Ethernet Port registration ∙ Restrictions on subnet masks ∙ Limitations on the T2N Send and Recv instructions 3 B 0 3 6 Usage Recommendations∙ Computer link protocol transmission Ethernet Port Overview Error HandlingEthernet Port Parts and Functions Preparing for Operation Hardware Registered trademarks Installation and WiringAppendix Contents Socket Interface Communication ……………………………………………………… System Configuration Examples System Configuration Using the Ethernet Port 10BASE2 LAN Standards and Terminology Series computer link protocol transmission slave port Basic Functionality T Series/PC Link Protocol Transmission 3 B 0 3 6 Series/PC link protocol transmission Socket Interface 3 B 0 3 6 Socket interface support Gateway Function 3 B 0 3 6 PC programmable controller gateway function 10BASE-T 3 B 0 3 6 Support for 10BASE-T Network Functional Specifications Ethernet Port Specifications TCP transmission control protocol Software Organization UDP User datagram protocol ARP Address resolution protocolIP Internet protocol Icmp Internet control message protocol Front Panel PU235N/245N External Dimensions 10BASE-T connecting connector Content DisplayedComponent Functions LED Display Preparing for Operation Hardware Connection to a 10BASE-T Network Connecting to the Network 10BASE-T Network Wiring EquipmentCatalog no Manufacturer Diameter Manufacturer 3 B 0 3 6 10BASE5Diameter Length Manufacturer Catalog no 3 B 0 3 6 10BASE2 Ethernet Port Setup Flowchart Software Ethernet Port Setup Flowchart Software Instruction format Ethernet Port Instruction SpecificationsOperand Important items Instructions Requests to the Ethernet Port Part 3 B 0 3 6 Transfer parameters a Send Meaning 3 B 0 3 6 Status BTermSTS Part Status 0AH Error Code Description Detailed Information Ethernet Port Error Responses PART1 Detailed Information Ethernet Port Error Responses PART2 T2N power on Ethernet Port Reset Reset request using the Send instruction 3 B 0 3 6 Reset request from the T2N IP address Parameter Setup RequestIP address format IP address acquisition Broadcast addresses Subnets and the subnet mask 3 B 0 3 6 Port number Parameter setup request using the Send instruction ∙ Message transmission UDP port number ⎯ 45 ⎯ Initialization mode Operating Mode Control RequestsStandby mode Run mode Shows the Ethernet Port mode transitions Operating mode control request using the Send instruction ⎯ 49 ⎯ Computer Link Protocol Transmission ∙ Remote UDP port number Sample Computer Link Protocol Program ⎯ 52 ⎯ ⎯ 53 ⎯ ⎯ 54 ⎯ ⎯ 55 ⎯ ⎯ 56 ⎯ PC Link Protocol Transmission Data write Register write request using the Send instruction RID Supplement T and C registers hold data that has flags attached XW/YW PC Link Protocol Transmission Data read Register read request using the Recv instruction Transferred register data length ⎯ 63 ⎯ Sample PC Link Protocol Transmission Program ⎯ 65 ⎯ ⎯ 66 ⎯ ⎯ 67 ⎯ Positioning and functionality Overview UDP Sockets UDP socket interface See figure TCP Socket Connection TCP socket interface See figures 6.3 TCP Connection Communication Procedure Overview Transmission Data Fragmentation in the UDP Socket Interface Ethernet Port Socket Interface Usage Notes ⎯ 73 ⎯ Handling of Transmitted Data in the TCP Socket Interface ⎯ 75 ⎯ Transmission Data Fragmentation in the TCP Socket Interface Packet Format/IP Datagram 3 B 0 3 6 Socket interface port numbers UDP socket interface notes 3 B 0 3 6 TCP socket interface notes ⎯ 81 ⎯ Socket Interface Information Socket identifier Socket Interface Information TCP UDP open request using the Send instruction Using the Ethernet Port Socket Interface ⎯ 85 ⎯ Error result UDP open processing example Ladder program flowchart Transmission data Broadcast transmission UDP transmission processing example Ladder program flowchart To the object socket in a single operation Methods for storing reception data Broadcast reception Status Send completion timeout TermSTS = 06H ⎯ 93 ⎯ ⎯ 94 ⎯ 3 B 0 3 6 UDP close request using the Send instruction UDP close processing example Ladder program flowchart Stcpportno 3 B 0 3 6 TCP open request using the Send instruction ¬The passive open timeout TCP open processing example Ladder program flowchart 3 B 0 3 6 TCP send request using the Send instruction ⎯ 101 ⎯ ⎯ 102 ⎯ TCP transmission processing example Ladder program flowchart 3 B 0 3 6 TCP receive request using the Recv instruction ⎯ 105 ⎯ ⎯ 106 ⎯ ⎯ 107 ⎯ ⎯ 108 ⎯ 3 B 0 3 6 TCP close request using the Send instruction ⎯ 110 ⎯ TCP close processing example UDP open request Sample ProgramsUDP sockets UDP close request UDP send request UDP receive request TCP open request passive 3 B 0 3 6 TCP sockets TCP open request active TCP close request TCP send request TCP receive request ⎯ 121 ⎯ RAS Information Special relays the renewing cycle of 100 ms T2N Special Relays and RegistersSpecial registers Station status format Operation mode and station status of Ethernet Port Down Information Down Information Error code H Interpretation Remote Port Verification Request Remote port verification request using the Send instruction ⎯ 127 ⎯ Remote Port Loopback for an Ethernet Port Remote port loopback request using the Send instruction Time Setting 3 B 0 3 6 Time set request using the Send instruction ⎯ 131 ⎯ RAS Information Readout RAS information readout request using the Recv instruction ⎯ 133 ⎯ ⎯ 134 ⎯ RAS information details Symbol DescriptionRAS Counters Mibif Mibtcp Mibip Mibudp MIB information Mibudp ... UDP protocol information Event Trace Items ∙ Event trace item See table ⎯ 139 ⎯ LED display State LED DisplayStates Indicated by the Erun LED 3 B 0 3 6 States Indicated by the Eacc LED Status error status TermSTS Status Meaning TermSTS Part Detailed Information Ethernet Port Error Responses Special registers Rclos If the Ethernet Port fails during operation TroubleshootingIf a Send or Recv instruction fails complete Replace the PU235N/245N Parameter setup request 3 B 0 3 6 If the Ethernet Port fails to enter run mode Operating mode control request ⎯ 151 ⎯ Ethernet Port side slave port Main port side Ethernet Port 3 B 0 3 6 If PC link protocol transmission fails ⎯ 154 ⎯ ⎯ 155 ⎯ Completion? Send request Receive request Open request 3 B 0 3 6 If Transmission Using TCP Sockets Fails Close request ⎯ 160 ⎯ ⎯ 161 ⎯ Check items Countermeasure 3 B 0 3 6 Network check items Ethernet Port Installation Environment and Base Unit Mounting Installation and Wiring Wiring Environment and Work Operations Network Wiring Separation from other wiring 3 B 0 3 6 Overview of wiring without protective pipes Or over Covered metal ducts or metal pipe Parallel separation Up toMeters Wiring routes Overview of panel internal wiringWiring path Securing coaxial cable ⎯ 168 ⎯ Inspection item Criterion Resolution procedure Appendix 1 Maintenance and InspectionPeriodic Inspection Table A.1 ⎯ 170 ⎯ Reference Appendix 2 Request Code TableTable A.2 Instructions Requests to the Ethernet Port Figure A.1 Status Structure Table A.3 TermSTS Part Appendix 3 Status Table Table A.4 TermSTS Part Table A.5 Detailed Information Ethernet Port Error Responses Figure A.2 Word Counts Considered with the PC Link Protocol When using the PC link protocol with the Ethernet Port Conditions for the above table Figure A.3 T2N Configuration when Using the PC Link Protocol Socket Transmission with the Ethernet Port Number of Words that can be Transmitted Using TCP/UDPWhen the PC link protocol is not used Figure A.5 T2N Configuration when Using the PC Link Protocol