Intel IXP43X PCB Overview, General Recommendations, Component Selection, Component Placement

Page 56

Intel® IXP43X Product Line of Network Processors—Hardware Design Guidelines

4.0General PCB Guide

4.1PCB Overview

Beginning with components selection, this chapter presents general PCB guidelines. In cases where it is too difficult to adhere to a guideline, engineering judgment must be used. The methods are listed as simple DOs and DO NOT’s.

This chapter does not discuss the functional aspects of any bus, or layout guides for any interfaced devices.

4.2General Recommendations

It is recommended that boards based on the IXP43X network processors employ a PCB stackup yielding a target impedance of 50 Ω ± 10% with 5 mil nominal trace width. That is, the impedance of the trace when not subjected to the fields created by changing current in neighboring traces.

When calculating flight times, it is important to consider the minimum and maximum impedance of a trace based on the switching of neighboring traces. Using wider spaces between the traces can minimize this trace-to-trace coupling. In addition, these wider spaces reduce crosstalk and settling time.

4.3Component Selection

•Do not use components faster than necessary

Clock rise (fall) time should be as slow as possible, as the spectral content of the waveform decreases

•Use components with output drive strength (slew-rate) controllable if available

•Use SMT components (not through-hole components) as through-hole (leaded) components have more stub inductance due to the protruding leads.

•Avoid sockets when possible

•Minimize number of connectors

4.4Component Placement

As shown in Figure 16 on page 57, when placing components, put:

•High-frequency components in the middle

•Medium-frequency around the high-frequency components

•Low-frequency components around the edge of the printed circuit board

Intel® IXP43X Product Line of Network Processors
HDG	April 2007
56	Document Number: 316844; Revision: 001US

Image 56

Contents Intel IXP43X Product Line of Network Processors Hardware Design GuidelinesApril Intel IXP43X Product Line of Network ProcessorsHDG Contents Figures Tables Document Number 316844 Revision 001US 001 Initial release § §Date Revision Description HDG Content Overview Chapter Name DescriptionRelated Documentation AcronymsList of Acronyms and Abbreviations Sheet 1 Term ExplanationOverview List of Acronyms and Abbreviations Sheet 2HDG Intel IXP435 Network Processor Block Diagram Typical Applications System Architecture Description System Memory MapIntel IXP43X Product Soft Fusible Features Signal Type DefinitionsSoft Fusible Features Sheet 1 Symbol DescriptionSoft Fusible Features Sheet 2 USB Host Each USB can be Enable separatelyDDRII/I Sdram Interface EthernetSignal Interface DDRII/I Sdram Interface Pin Description Sheet 1Type Name Device-Pin Connection Terminatio Description FieldDDRII/I Sdram Initialization DDRII/I Sdram Interface Pin Description Sheet 2Type Pull Name Recommendations Field Down Expansion Bus Signal Recommendations Sheet 1Expansion Bus Reset Configuration Straps Expansion Bus Signal Recommendations Sheet 2Boot/Reset Strapping Configuration Sheet 1 Name Type Pull Recommendations Field DownBoot/Reset Strapping Configuration Sheet 2 Setting Intel XScale Processor Operation Speed 3 8-Bit Device InterfaceIntel XScale Processor Cfg0 Cfg1 Cfgenn Actual Core Speed MHz4 16-Bit Device Interface Flash Interface 16-Bit Device InterfaceUart Interface Flash Interface ExampleUart Signal Recommendations MII Interface Uart Interface ExampleMII NPE C Signal Recommendations Sheet 1 Signal Interface MIIMII NPE a Signal Recommendations Device Connection, MII MII NPE C Signal Recommendations Sheet 2MAC Management Signal Recommendations NPE a and NPE C Gpio Interface MII Interface ExampleDesign Notes Gpio Signal RecommendationsUSB Interface USB Host Signal Recommendations Name Type Pull Description Field DownCommon Mode Choke Host Device Type Pull Name Description Field Down Utopia Level 2 InterfaceUtopia Level 2/MIIA UTPOPDATA4 UTPOPDATA75UTPOPADDR40 UtpopfciClav UtpipfciUtpipsoc ETHARXDATA30 EtharxclkUTPIPDATA5 UTPIPDATA6UTPIPDATA7 UTPIPADDR40HSS Interface Device ConnectionHigh-Speed, Serial Interface HSSTXDATA0HSSTXCLK0 HSSRXDATA0SSP Interface HSS Interface ExampleSynchronous Serial Peripheral Port Interface PCI Interface Serial Flash and SSP Port SPI Interface ExamplePCI Controller Sheet 1 PCI Interface Block Diagram PCI Controller Sheet 2Pciintan PciclkinConnect signal to same pin between PCI Parity Two devices PCI Option InterfacePCI Host/Option Interface Pin Description Sheet 1 Type Option Description Name Device-Pin Connection FieldOn the Option device, these signals are not Signal PCIREQN0 to one PCIREQN30 inputs to the HostPCI Host/Option Interface Pin Description Sheet 2 Type Option Name Device-Pin Connection Description FieldJtag Interface PCI Host/Option Interface Pin Description Sheet 3Clock Signals Clock SignalsInput System Clock Clock OscillatorRecommendations for Crystal Selection Nominal Name Voltage Description PowerPower Supply Power Sequence Reset TimingDecoupling Capacitance Recommendations VCC Decoupling§ § Component Placement PCB OverviewGeneral Recommendations Component SelectionComponent Placement on a PCB Stack-Up SelectionControlled-impedance traces Low-impedance power distribution Layer Stackup General Layout and Routing Guide General Layout GuidelinesSignal Changing Reference Planes General Component SpacingGood Design Practice for VIA Hole Placement Clock Signal Considerations Pad-to-Pad Clearance of Passive Components to a PGA or BGACrosstalk MII Signal ConsiderationsUSB V2.0 Considerations Trace Impedance Power and Ground PlaneEMI Design Considerations § § Electrical Interface Topology@33 MHz Tcyc = 30 nSec Tval = 11 nSec Tprop = 10 nSecParameter Routing Guidelines Clock DistributionPCI Address/Data Routing Guidelines Trace Length Limits PCI Clock Routing GuidelinesSignal Loading Routing GuidelinesDdrii / Ddri Sdram IntroductionDDRII/I Signal Groups Group Signal Name DescriptionDrasn / Ddrrasn Dcasn / DdrcasnDDR Sdram Supported Ddri 32-bit Sdram Configurations Supported Ddrii 32-bit Sdram ConfigurationsSupported Ddri 16-bit Sdram Configurations SizeaSupported Ddrii 16-bit Sdram Configurations DDRII/DDRI Rcomp and Slew Resistances Pin RequirementsAddress Size Leaf Select Total Technology Arrangement BanksDDR Clock Timings DDR-II Symbol Parameter Units Min MaxDdrii OCD Pin Requirements DDR Sdram Write Timings DDRII-400 MHz Interface -- Signal Timings Symbol Parameter Minimum Nominal Maximum UnitsDDR II/I Sdram Interface -- Signal Timings Symbol Parameter Minimum Nom Maximum UnitsTiming Relationships Printed Circuit Board Layer StackupTiming Relationships Signal Package Lengths Sheet 1Group Signal Name Length mil Signal Package Lengths Sheet 2 Signal Package Lengths Sheet 3 Clock GroupData and Control Groups Parameter DefinitionDdrii Data and Control Signal Group Routing Guidelines DCB70/DDRCB70, DDQ310 / DDRDQ310Ddrii Command Signal Group Routing Guidelines Signal Group Members§ §