Epson DW073 instruction manual Quick Check, Horizontal Checking for SIDE-TO-SIDE Tilt Error

Page 18

English

BEAM

APPROX. 50 FT.

APPROX. 50 FT.

SURFACE 1

SURFACE 2

FIG. AA - UNIT FACING RIGHT

BEAM

 

APPROX. 50 FT.

APPROX. 50 FT.

SURFACE 1

SURFACE 2

FIG. BB - UNIT FACING LEFT

Mount your Rotary Laser on a tripod so it is aimed front-to-back toward the vertical surfaces. (next page)

Level the Laser, following the procedure in the “Horizontal Leveling” section of this manual.

Quick Check:

1.Compare the position of the bubbles in the front and rear vials (Fig. AA).

2.If the two bubbles are not in about the same position in their vials, (both about centered) have your Rotary Laser calibrated at a DEWALT service center.

Turn the unit on so that the lasers are on and rotating.

Go to surface #1 and mark the center of the beam. If it is difficult to see the beam, use your Laser Enhancement Glasses, Target Card or optional DW0732 Digital Laser Detector.

Go to surface #2 and mark the center of the beam.

Loosen the screw holding the Laser to the tripod, but do not remove the Laser.

Rotate the Laser 180˚ (Fig. BB)

Level the Laser again, following the procedure in the “Horizontal Leveling” section of this manual.

Turn the unit on if it is not already on, so the lasers are on and rotating.

Go to surface #1 and mark the center of the beam.

Go to surface #2 and mark the center of the beam.

Measure the difference between the marks on surface #1.

Measure the difference between the marks on surface #2.

The difference between the marks on surface #1 must equal the difference between the marks on surface #2. If these are not equal, there was user set up or marking error.

If the difference between the marks on surface #1 is 1/4" or less, the Laser is properly calibrated.

If the difference between the marks on surface #1 is more than 1/4", have your Rotary Laser calibrated at a DEWALT service center.

HORIZONTAL CHECKING FOR SIDE-TO-SIDE TILT ERROR

Set up tripod midway between 2 vertical surfaces 100' from each other.

Mount your Rotary Laser on a tripod so that it is aimed side-to-side toward the vertical surfaces.

Level the Laser, following the procedure in the “Horizontal Leveling” section of this manual.

Turn the unit on so that the lasers are on and rotating.

Go to surface #1 and mark the center of the beam. If is difficult to see the beam use one of the aids mentioned earlier.

Go to surface #2 and mark the center of the beam.

Loosen the screw holding the Laser to the tripod but do not remove the Laser.

Rotate the Laser 180˚.

Level the Laser again, following the procedure in the “Horizontal Leveling” section.

16

Image 18
Contents Guide Dutilisation Manual DE Instrucciones Page General Safety Rules For Battery Operated Tools IntroductionAdditional Safety Rules Important Safety Instructions for Battery PacksService Read ALL Instructions Rbrc SealImportant Safety Instructions for Battery Chargers Indicator Light Operation Charge Indicators Using Automatic Tune-Up ModeCharging Procedure HOT/COLD Pack DelayCharger Cleaning Instructions Problem Power LineLeaving the Battery Pack in the Charger Important Charging NotesLaser Safety Operating TipsProduct Emits Laser Radia Tion do not Stare Into Laser Beam Installing and Removing the Battery Pack Control PanelBump Sensor Controls SettingBump Sensor Flashing LED Warning Light onlyMounting on a Tripod Two-Position Pivoting HeadWall, Floor & Tripod Mounts Floor MountWall Mount Horizontal Leveling Vertical PlumbingTarget Card Manual Head Rotation ButtonLaser Enhancement Glasses Digital Laser DetectorCeiling Installation ApplicationsWall Layout Foundations MaintenanceTilt Error Checks Deck BuildingHorizontal Checking for SIDE-TO-SIDE Tilt Error Quick CheckAccessories Repair Cone Error CheckPlumb Error Check Battery will not Lock in Place Three Year Limited WarrantyTroubleshooting Guide Laser will not Turn onRotating Laser Beam is Difficult to see Indoors Laser Rocks When Positioned on the FloorBump Sensor Warning LED Light is Flashing Cold Storage InformationMesures DE Sécurité Électricité Règles générales de sécurité concernant les outils à pilesZone DE Travail Sécurité PersonnelleRègles de sécurité additionnelles Utilisation ET Entretien DE L’OUTILEntretien Consignes de sécurité importantes concernant les bloc-piles Lire Toutes LES DirectivesSceau Rbrcmc Utilisation du mode Tune-upMC Automatique Calibre AWGMéthode de Chargement Problemes Reliés À LA Source DE CourantChargeurs Fonctionnement des voyants Voyants de chargeBLOC-PILES Laissé Dans LE Chargeur Mesures de sécurité relatives au laser rotatif Conseils d’utilisationDirectives Concernant LE Nettoyage DU Chargeur Installation et retrait du Bloc-pilesIndicateur DE Décharge DU BLOC-PILES Panneau de commandeDétecteur d’impact Arret DU LaserTête pivotante à deux positions Commandes DU Détecteur D’IMPACTMode DE Détection no Témoin À DEL Clignotant SeulementInstallation SUR Trépied Installation au sol, au mur ou sur trépiedInstallation AU SOL Installation AU MURNiveau horizontal Pignon et crémaillère afin de maintenir le réglageBouton de réglage de La tête pivotante Niveau verticalVerres d’accentuation à laser Carte indicatrice de ciblesDétecteur laser numérique Installation au plafond Préparation du murFondations Vérification de l’étalonnage Construction d’une terrasseEntretien Défauts D’INCLINAISONVérification rapide Vérification DU Défaut DE Cône Défaut DE VerticaleGarantie limitée de trois ans AccessoiresRéparations Contrat D’ENTRETIEN Gratuit D’UN ANLE Laser Refuse DE SE Mettre EN Marche Guide de dépannageLA Pile N’EST PAS Bien Enclenchée LA Tête Pivotante Projette Deux Traits Laser’OUTIL Bascule LORSQU’ON LE Place AU SOL Réglage DE L’OUTIL Pour UNE Installation AU MURObtention DU Niveau Vertical Information Concernant LE Rangement AU FroidSeguridad Eléctrica IntroducciónÁrea DE Trabajo Seguridad PersonalReglas adicionales de seguridad ServicioLEA Todas LAS Instrucciones El sello Rbrc Cargadores Procedimiento de cargaOperación de la luz indicadora Indicadores de carga Linea DE Alimentacion ProblematicaUtilización de la modalidad Tune UpMC Automática Retraso POR Unidad CALIENTE/FRIANotas importantes sobre la carga Seguridad acerca de dispositivos LáserInstrucciones Para LA Limpieza DEL Cargador Sugerencias para operar la herramienta Instalación y remoción del grupo de baterías Tablero de controlControles DEL Sensor DE Golpes Sensor de golpesVelocidades DE Rotación AjusteCabeza pivotante de dos posiciones Montaje EN LA Pared Montaje en la pared, piso & trípodeMontaje Sobre Tripode Montaje Sobre PisoNivelación horizontal Plomada vertical Botón de rotación manual de la cabezaGafas intensificadoras para láser Tarjeta de miraDetector digital de láser Aplicaciones Instalación de techoReplanteo de paredes Mantenimiento FundacionesConstrucción de patios entablados Verificación de calibración de campoVerificación DEL Error DE Inclinación Verificación rápidaVerificación DE Error DE Cono Verificación DE Error DE PlomadaPóliza de Garantía AccesoriosReparaciones Garantía limitada por tres añosGarantía DE Reembolso DE SU Dinero POR 90 Días Reemplazo DE LAS Etiquetas DE Advertencia GratuitoEL Láser no SE Prende Guía de solución de problemasLA Bateria no Quiere Acoplarse EN SU Lugar LA LUZ DEL Sensor DE Golpes Está ParpadeandoEL Láser SE Mece Cuando SE Coloca EN EL Piso Informacion Para Almacenamiento FrioPage Form No