Epson DW073 instruction manual Accessories Repair, Cone Error Check, Plumb Error Check

Page 19

Turn the unit on if not already on, so that the lasers are on and rotating.

Go to surface #1 and mark the center of the beam.

Go to surface #2 and mark the center of the beam.

The difference between the marks on surface #1 must equal the difference between the marks on surface #2. If these are not equal, there was user set up or marking error.

If the difference between the marks on surface #1 is 1/4" or less, the Laser is properly calibrated.

If the difference between the marks on surface #1 is more than 1/4", have your Rotary Laser calibrated at a DEWALT service center.

CONE ERROR CHECK

Your DEWALT Rotary Laser contains 2 laser diode assemblies. It is highly unlikely that both lasers would have shifted by identical amounts. The easiest way to test for possible “cone error” is to compare the two laser beams.

Level the laser, following instructions in the “Horizontal Leveling” section of this manual.

Quick Check:

1.Turn the unit on so that the lasers are on and rotating.

2.You should see a single red line on a vertical surface. If you see a double line, have your Rotary Laser calibrated by a DEWALT service center.

Turn unit on so that the lasers are on but NOT rotating.

Using the Manual Rotation Button, rotate the head so that the lasers appear as two dots on a vertical surface about 25 feet away.

Compare the vertical position of the center of each laser beam. The centers should be within 3/32"(vertically) of each other.

If the centers of the two beams differ by more than 3/32" (verti- cally), then have your Rotary Laser calibrated at a DEWALT ser- vice center.

PLUMB ERROR CHECK

Set up a tripod about 25 feet from a vertical surface.

Mount your Rotary Laser on the tripod.

Following the procedure in the “Two Position Pivoting Head” section of this manual, set the Rotary Laser head in the plumb position.

Hang a plumb bob from the vertical surface.

Level the laser, following instructions in the “Vertical Plumbing” section of this manual.

Turn the unit on so that the lasers are on and rotating.

Rotate the laser on the tripod so that the beam is in the line with the plumb bob.

Ensure that the laser is still level.

If the beam lies along the same line as the plumb bob string, then the calibration is acceptable.

If the beam does not lie along the same line as the plumb bob string, have your Rotary Laser calibrated at a DEWALT service center.

Accessories

Recommended accessories for use with your tool are available at extra cost from your local service center. If you need any assistance in locating any accessory, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 or call 1-800-4-DEWALT. (1-800-433-9258) See our catalog on the World Wide Web at www. DEWALT.com.

CAUTION: The use of any non-recommended accessory may be hazardous.

Repair

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by certified service centers or other qualified service organizations, always using identical replace- ment parts.

English

17

Image 19
Contents Guide Dutilisation Manual DE Instrucciones Page Introduction General Safety Rules For Battery Operated ToolsImportant Safety Instructions for Battery Packs Additional Safety RulesService Rbrc Seal Read ALL InstructionsImportant Safety Instructions for Battery Chargers HOT/COLD Pack Delay Using Automatic Tune-Up ModeCharging Procedure Indicator Light Operation Charge IndicatorsImportant Charging Notes Problem Power LineLeaving the Battery Pack in the Charger Charger Cleaning InstructionsOperating Tips Laser SafetyProduct Emits Laser Radia Tion do not Stare Into Laser Beam Control Panel Installing and Removing the Battery PackFlashing LED Warning Light only SettingBump Sensor Bump Sensor ControlsFloor Mount Two-Position Pivoting HeadWall, Floor & Tripod Mounts Mounting on a TripodWall Mount Vertical Plumbing Horizontal LevelingDigital Laser Detector Manual Head Rotation ButtonLaser Enhancement Glasses Target CardApplications Ceiling InstallationWall Layout Deck Building MaintenanceTilt Error Checks FoundationsQuick Check Horizontal Checking for SIDE-TO-SIDE Tilt ErrorCone Error Check Accessories RepairPlumb Error Check Laser will not Turn on Three Year Limited WarrantyTroubleshooting Guide Battery will not Lock in PlaceCold Storage Information Laser Rocks When Positioned on the FloorBump Sensor Warning LED Light is Flashing Rotating Laser Beam is Difficult to see IndoorsSécurité Personnelle Règles générales de sécurité concernant les outils à pilesZone DE Travail Mesures DE Sécurité ÉlectricitéUtilisation ET Entretien DE L’OUTIL Règles de sécurité additionnellesEntretien Lire Toutes LES Directives Consignes de sécurité importantes concernant les bloc-pilesSceau Rbrcmc Calibre AWG Utilisation du mode Tune-upMC AutomatiqueFonctionnement des voyants Voyants de charge Problemes Reliés À LA Source DE CourantChargeurs Méthode de ChargementBLOC-PILES Laissé Dans LE Chargeur Conseils d’utilisation Mesures de sécurité relatives au laser rotatifDirectives Concernant LE Nettoyage DU Chargeur Bloc-piles Installation et retrait duArret DU Laser Panneau de commandeDétecteur d’impact Indicateur DE Décharge DU BLOC-PILESTémoin À DEL Clignotant Seulement Commandes DU Détecteur D’IMPACTMode DE Détection no Tête pivotante à deux positionsInstallation AU MUR Installation au sol, au mur ou sur trépiedInstallation AU SOL Installation SUR TrépiedPignon et crémaillère afin de maintenir le réglage Niveau horizontalNiveau vertical Bouton de réglage de La tête pivotanteCarte indicatrice de cibles Verres d’accentuation à laserDétecteur laser numérique Préparation du mur Installation au plafondFondations Défauts D’INCLINAISON Construction d’une terrasseEntretien Vérification de l’étalonnageVérification rapide Défaut DE Verticale Vérification DU Défaut DE CôneContrat D’ENTRETIEN Gratuit D’UN AN AccessoiresRéparations Garantie limitée de trois ansLA Tête Pivotante Projette Deux Traits Laser Guide de dépannageLA Pile N’EST PAS Bien Enclenchée LE Laser Refuse DE SE Mettre EN MarcheInformation Concernant LE Rangement AU Froid Réglage DE L’OUTIL Pour UNE Installation AU MURObtention DU Niveau Vertical ’OUTIL Bascule LORSQU’ON LE Place AU SOLSeguridad Personal IntroducciónÁrea DE Trabajo Seguridad EléctricaServicio Reglas adicionales de seguridadLEA Todas LAS Instrucciones El sello Rbrc Procedimiento de carga CargadoresRetraso POR Unidad CALIENTE/FRIA Linea DE Alimentacion ProblematicaUtilización de la modalidad Tune UpMC Automática Operación de la luz indicadora Indicadores de cargaSeguridad acerca de dispositivos Láser Notas importantes sobre la cargaInstrucciones Para LA Limpieza DEL Cargador Sugerencias para operar la herramienta Tablero de control Instalación y remoción del grupo de bateríasAjuste Sensor de golpesVelocidades DE Rotación Controles DEL Sensor DE GolpesCabeza pivotante de dos posiciones Montaje Sobre Piso Montaje en la pared, piso & trípodeMontaje Sobre Tripode Montaje EN LA ParedNivelación horizontal Botón de rotación manual de la cabeza Plomada verticalTarjeta de mira Gafas intensificadoras para láserDetector digital de láser Instalación de techo AplicacionesReplanteo de paredes Verificación de calibración de campo FundacionesConstrucción de patios entablados MantenimientoVerificación rápida Verificación DEL Error DE InclinaciónVerificación DE Error DE Plomada Verificación DE Error DE ConoGarantía limitada por tres años AccesoriosReparaciones Póliza de GarantíaReemplazo DE LAS Etiquetas DE Advertencia Gratuito Garantía DE Reembolso DE SU Dinero POR 90 DíasLA LUZ DEL Sensor DE Golpes Está Parpadeando Guía de solución de problemasLA Bateria no Quiere Acoplarse EN SU Lugar EL Láser no SE PrendeInformacion Para Almacenamiento Frio EL Láser SE Mece Cuando SE Coloca EN EL PisoPage Form No