GE ZVC30, ZVC42, ZVC48, ZVC36 OBSERVETHEFOLLOWINGa, Never Pick UP a Flaming PAN-You may be burned

Page 3

Installation Instructions

CAUTION: To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces or garages.

WARNING: TO REDUCE THE RISK OF

A RANGE TOP GREASE FIRE:

A.Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

B.Always turn hood ON when cooking at high heat or when flambeing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

C.Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.

D.Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING:TOREDUCETHERISKOFINJURY

TOPERSONSINTHEEVENTOFARANGETOPGREASEFIRE,

OBSERVETHEFOLLOWINGa:

A.SMOTHER FLAMES with a close-fitting lid, cookie sheet or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately,

EVACUATE AND CALL THE FIRE DEPARTMENT.

B.NEVER PICK UP A FLAMING PAN—You may be burned.

C.DO NOT USE WATER, including wet dishcloths or towels— a violent steam explosion will result.

D.Use an extinguisher ONLY if:

1)You know you have a Class ABC extinguisher, and you already know how to operate it.

2)The fire is small and contained in the area where it started.

3)The fire department is being called.

4)You can fight the fire with your back to an exit.

aBased on “Kitchen Firesafety Tips” published by NFPA.

3

Image 3
Contents Installation Instructions Read these instructions completely and carefully Installation InstructionsFor Monogram local service in your area, call For Monogram Parts and Accessories, callOBSERVETHEFOLLOWINGa Never Pick UP a Flaming PAN-You may be burnedUse an extinguisher only if Contents Design InformationProduct Clearances ZVC30 Product DimensionsZVC36 34-1/2 ″Insert Sleeve 21-1/4″ ZVC4239-1/2″ 40-1/2″46-1/2″ ZVC48Power Supply Advance PlanningAdvance Planning Duct Fittings Flexible ductingDo not use flexible plastic ducting Open hood carton Remove the liner, foam and cardboard Installation PreparationTools and Materials Required Remove the PackagingCheck Installation Hardware Remote Mounting of the Control WiredParts Provided Ceiling ducting Wall Installation PreparationDUCTWORK, Wiring Locations Above bottom edge of insert sleeveCenter Cooktop Countertop Front view Island Installation PreparationInstallation height Plan the Location of the Hood and DuctworkRemote Location for Control Remote Mounting of the Control WiredBracket CountertopCutout opening Wall MountingInstall Hood Liner Connect Electrical Verify that power is turned off at the sourceInstall Insert Sleeve Bolts Install Damper PlateInstall Blower Motor Connect Wiring HarnessWiring Finalize Installation Install FiltersDélai d’exécution 1 à 3 heures Instructions d’installationMise EN Garde Pour une Lisez ces instructions entièrement et attentivementFeu doux ou moyen Avertissement Pour RéduireInformation de conception Table DES MatièresDégagements Dimensions DE L’APPAREIL 4 po 34-1/2 po Dimensions et spécifications en pouces Dimensions externes 8 po 46-1/2 po 38-1/2 po 13 po Planification PlanificationAlimentation Électrique ’UTILISEZ PAS de conduit en plastique flexible Raccords DE ConduitsRetrait DE L’EMBALLAGE Préparation pour l’installationLocalisez les pièces emballées avec la hotte Vérification DU Matériel D’INSTALLATIONMontage DES Commandes À Distance Câblées Pièces FourniesPréparation du mur pour l’installation ET DU CâblageConduit de ventilation de plafond De cuisson Comptoir Vue frontale Préparation pour l’installation en îlotMontage DES Commandes À Distance Câblées Positionnement DES Commandes À DistanceAvertissement Coupez Comptoir Montage MuralRemontez les languettes sur Fixez la doublure au meuble à l’aide des 6 vis fournies Etape 1 Installation DE LA Doublure DE LA HotteAvertissement Si le câblage Etape 3 Installation DE LA Gaine DE Hotte Encastrable Etape 4 Installation DU Registre À Guillotine Etape 6 Connexion DU Faisceau Électrique Etape 5 Installation DES Moteurs DE VentilateursEtape 7 Installation DES Filtres Etape 8 Finalisation DE ’INSTALLATIONRetirez le film protecteur des filtres Page Instrucciones de instalación RLea estas instrucciones por completo y con detenimientoTiempo de finalización de 1 a 3 horas Nunca Levante UNA Sartén EN LLAMAS-Usted puede quemarse SOBREUNAESTUFA,CUMPLACONLOSSIGUIENTESPUNTOSª30″ mínimo requerido 36″ máximo recomendado 36″ min Información de diseñoContenidos Espacios DEL ProductoUbicación remota del control Dimensiones DEL ProductoEl revestimiento provisto Revestimiento a medidaZVC36 La funda del encastre 39-1/2″ZVC48 Planificación previa ADVERTENCIAUna conexiónSuministro DE Energía Ashrae Accesorios Para ConductosPrecaución Use guantes para protegerse de lados afilados Quite EL EnvoltorioMontaje Remoto DEL Control CON Cables Preparación para la instalaciónPiezas Provistas Controle LAS Piezas DE InstalaciónPreparación para la instalación en pared Ubicaciones DE LOS Conductos Y CableadoConductos en el cielorraso Preparación para la instalación en isla Principal Advertencia Desconecte laMontaje Remoto DEL Control CON Cables Ubicación Remota DEL ControlMostrador DE Encimera Aplique silicona alrededor de la aberturaColoque el control dentro de la abertura Encuadre la abertura para que entre el revestimiento Paso 1 Instale EL Revestimiento DE LA CampanaADVERTENCIASi el cableado Paso 2 Conecte LA ElectricidadNota El conducto doméstico debe ubicarse a Paso 3 Instale LA Funda DEL EncastrePaso 4 Instale LA Placa DEL Regulador DE Tiro Paso 6 Conecte EL Arnés DE Cableado Paso 5 Instale EL Motor DEL VentiladorPaso 7 Instale LOS Filtros Paso 8 Finalice LA InstalaciónQuite la película protectora de los filtros Gancho Notas Notas GE Consumer & Industrial