Homelite UT10946 manual Maintenance

Page 41

MAINTENANCE

6.Place the chain drive links (I) into the bargroove (J)asshowninillustration (K). Position the chain so there is a loop at the back of the bar as shown in illustration (K). Hold chain in posi- tion on the bar and place the loop around the sprocket (L) as shown in illustration (M). Fit the bar flush against the mounting surface so that the bar studs (N) are in the long slot of the bar.

NOTE: When placing the bar on the bar studs in step 6, assure that the adjusting pin (O) is in the chain ten- sion pin hole as shown in illustration (P) as illustrated below.

ENTRETIEN

6.Mettre les maillons d’entraînement de la chaîne (I) dans la fente du guide- chaîne (J), comme montré sur l’illustration (K). Mettre la chaîne en positiondemanièreàformeruneboucle à l’arrière de la barre, comme montré sur l’illustration (K). Maintenir la chaîne en position sur le guide et placer la boucle autour du pignon (L), comme montré sur l’illustration (M). Monter le guide de niveau contre la surface de montage de telle manière que les goujons (N) du guide soient dans la fente longue du guide.

REMARQUE – Au moment de la pose des goujons du guide à l’étape 6, vérifier que le goujon de réglage (O) se trouve dans le trou du goujon de tension de la chaîne, comme montré sur l’illustration (P) ci-dessous.

MANTENIMIENTO

6.Insertar los eslabones (I) de la cadena en la ranura (J) de la barra [tal como se muestra en la ilustración (K)]. Al colocar la cadena, dejar un bucle en la parte trasera de la barra, tal como se muestra en la ilustración (K). Sostener la cadena en esa posición y pasar el bucle alrededor de la rueda dentada (L), tal como se muestra en la ilustración (M). Colocar la barra a ras de la superficie de montaje, dejando los pernos (N) introducidos en la ranura larga de la barra.

NOTA: en el paso 6, al colocar la barra en lospernos,asegurarsedequeeltornillode ajuste de tensión (O) quede introducido en su agujero correspondiente, tal como se muestra en la ilustración (P).

K

J

I

M

P

 

 

O

 

N

 

E

 

L

 

D

 

41

Image 41
Contents Chain Saw / Scie De Chaine / Motosierra Contents Table DES Matières Índice Identificación DE Componentes Product IdentificationIdentification DU Produit Seguridad SafetySécurité Precauciones frente a la tensión de retroceso Precautions Against KickbackPrécautions pour éviter le rebond du guide-chaîne Atención Mesures de sécurité élémentaires Basic Safety PrecautionsPrecauciones básicas de seguridad Poussée et tractionRopa de seguridad Safety ApparelVêtements de sécurité Rebond du guide-chaîne KickbackTensión de retroceso Refueling do not SmokeEntretien MaintenanceMantenimiento Cutting/Work AreaComprendre les dispositifs de sécurité de l’appareil Understanding Your Chain Saw Safety DevicesProtection anti-rebond SAFE-T-TIP Protección del borde Anti-retroceso SAFE-T-TIPGuide-chaînes Chaîne à faible rebondCadenas de sierra con tensión de retroceso baja Barras de guíaFrein de chaîne Chain BrakeFreno de la cadena Position DE Marche Position DE FreinFueling Operation Utilisation OperaciónRemplissage en carburant Abastecimiento de combustibleBurn injury Check for fuel leaks, if any are foundCorrect before use to prevent fire or Chain Oil System OperationDispositif de lubrification de la chaîne Sistema de lubricación de la cadenaStarting the Engine Démarrage du moteur Arranque del motor Operation Marche Volet DE DépartArrêt du moteur Stopping the EngineParada del motor Remarque Démarrage D’UN Moteur ChaudPréparatifs pour la coupe Preparation for CuttingPreparación para el corte Comment tenir les poignéesProper Cutting Stance Basic Cutting ProcedurePosition correcte du corps pour la coupe Postura de corte adecuadaPrecauciones relativas al área de trabajo Work Area PrecautionsPrécautions sur l’aire de travail Ajuste del carburador Carburetor AdjustmentRéglage du carburateur Ajuste de la velocidad de marcha lenta Idle Speed AdjustmentRéglage du ralenti Operación del freno de la cadena Chain Brake OperationUtilisation du frein de chaîne Abattage d’un arbre Tree FellingCaída de árboles Conditions particulièrement dangereuses135 Nota Cm or 1/10 DIARemarque Racines échasses Buttress RootsRaíces zanco BuckingCorte del tronco con un calzo Bucking with a WedgeTronçonnage utilisation d’un coin Billes sous tension Logs Under StressLeños sometidos a tensión Types of Cutting UsedEliminación de ramas y poda Limbing and PruningÉbranchage et élagage Load Charge Carga Ramas/arbustos sometidos a tensión SpringpolesEffet de ressort Maintenance Chart MaintenanceCalendrier d’entretien EntretienTable de mantenimiento MantenimientoAssembling Bar and Chain Maintenance Entretien MantenimientoArmado con barra y cadena Assemblage du guide et de la chaîneOuter guide bar plate E Maintenance EntretienThen remove the clutch cover D Maintenance Maintenance Chain Tension Tension de la chaîne Tensión de la cadena Mise EN Garde Mantenimiento de la cadena Chain MaintenanceEntretien de la chaîne Cómo afilar los cortadores How to Sharpen the CuttersAffûtage des gouges Correcto Ángulo de afilamiento de la placa superiorÁngulo de la placa lateral Angle d’affûtage de la plaque latéraleSeparación de los reguladores de profundidad Tensión DE RetrocesoLima Plana Empalmador DE Reguladores DE Profundidad Lime Plate Guide DE Jauge DE ProfondeurBar with any of the following faults should be replaced Montaje del protector de punta SAFE-T-TIP Mounting SAFE-T-TIP Nose GuardMontage de la protection de pointe SAFE-T-TIP Filtro de aire Air FilterFiltre à air Unidad del arrancador Starter UnitDispositif de démarrage Motor EngineMoteur Filtre à carburant Fuel FilterFiltro del combustible Spark PlugSilencieux pare-étincelles Spark Arresting MufflerSilenciador con apagachispas NettoyageChain Brake Combinaciones DE Barra Y Cadena BAR and Chain CombinationsCombinaisons DE GUIDE-CHAÎNE ET DE Chaîne Using Troubleshooting Chart TroubleshootingUtilisation du tableau de localisation des pannes Problème Cause Possible SolutionLocalisation DES Pannes Problema Posible Causa Solución Resolución DE ProblemasUtilización de la tabla de resolución de problemas Almacenamiento de la motosierra 1 mes o más Storing Chain Saw 1 month or longerEntreposage de la tronçonneuse un mois ou plus Datos Técnicos Technical DataDonnées Techniques Save Your Sales Slip WarrantyOwners Warranty Responsibilities Manufacturers Warranty CoverageMaintenance Requirements Emissions Maintenance Schedule and Warranted Parts ListConservez Votre Reçu GarantieGarantie DU Fabricant Guarde SU Comprobante DE Venta GarantiaResponsabilidades DEL Propietario CON Respecto a LA Garantia Page Page Avertissement

UT10946 specifications

The Homelite UT10946 is a highly regarded tool in the outdoor power equipment market, particularly known for its efficiency and reliability. Designed for homeowners and gardening enthusiasts, this model combines power with ease of use, making it an ideal choice for various landscaping tasks.

One of the standout features of the UT10946 is its powerful 25cc 2-cycle engine. This engine provides ample power for tackling a range of tasks, from light trimming to heavier brush clearing. Its lightweight design enhances maneuverability, allowing users to navigate easily around gardens and landscapes without fatigue. This is particularly beneficial during extended periods of use.

The Homelite UT10946 is equipped with an automatic line advance system, which eliminates the need for manual adjustments. This feature ensures that users can work continuously without interruptions for line replacement, ultimately increasing productivity. The tool utilizes a .095-inch trimmer line, which strikes a balance between durability and efficiency, effectively coping with thick grass and tough weeds.

Ergonomics play a crucial role in the design of the UT10946. The trimmer features an adjustable handle, allowing users to customize their grip for better control and comfort. This ergonomic consideration reduces strain on the hands and arms, particularly during lengthy jobs. A padded shoulder strap is also included, which provides additional support and balance as users maneuver the trimmer across uneven terrain.

The unit's ease of starting is enhanced by the inclusion of a primer bulb and choke mechanism, allowing for a quicker ignition process. This is particularly advantageous for users who are not as experienced with starting gas-powered equipment.

In terms of construction, the Homelite UT10946 boasts a robust build designed to withstand the rigors of outdoor use. Its durable materials ensure that it can handle the challenges of various weather conditions, contributing to its longevity.

In summary, the Homelite UT10946 offers a blend of power, convenience, and user-friendliness. With features such as a powerful engine, automatic line advance, ergonomic design, and easy starting mechanisms, it stands out as a reliable choice for homeowners looking to maintain their gardens and landscapes efficiently.