Software Execution Messages | 3Com DSA-3CV1100-02 specs

78MANAGING THE VCN ACCESS CONCENTRATOR

Figure 54 Software Execution Messages

Start executing main!

Watchdog initialized OK !

After the software download, the port starts to execute the software from the flash memory. The port runs a selftest, and the messages shown in Figure 55 appear:

Figure 55 Port Self-test Message

Ethernet MAC address is 00.c0.da.40.80.54

HDLC selftest passed!

Ethernet selftest passed!

I2C selftest passed!

SMC2 task created!

SMC2 task started!

SMC2 task created!

SMC2 task started!

SMC2 selftest passed!

VDSL selftest passed!

MNG task created!

MNG task started!

AGENT task created!

IP task created!

IP task started!

LED task created!

LED task started!

LMA task created

LMA task started

Telnet CLI task created

Then the Login prompt appears; refer to page 52 for more information.

If, instead of the messages in Figure 55 through Figure 55, one of the following messages appear, the software load failed:

■Flash Error

■SW image validation failed

Try to load the software again. If the problem persists, replace the port in the VCN AC.

Image 78

3Com DSA-3CV1100-02 service manual Software Execution Messages

Contents

Visitor and Community Network Access Concentrator Release 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Contents Troubleshooting 127130 Inability to Connect Broken Session 131 Online Technical Services 141 World Wide Web Site 3Com FTP Site 142143 Page Conventions List conventions that are used throughout this guideIcon Description Year RelatedDocumentation Compliance Visitor Major Features BenefitsFeatures Community Overview Applications MTU/MDU Application VCN AC Features VCN AP VCN AC Front Panel VCN AC Front Panel LEDs Features Real Time LED IndicationsLocal Management State Used to Central Management Remote Management Overview Installing the VCN Access Concentrator Safety Precautions Précautions de SécuritéSicherheitsvorkeh- rungen Preparing the Site For the VCN AccessVisitor and Community Network system is installed Concentrator Installing the VCN Access Concentrator Punch-down Block with a Patch Panel Installing the VCN Access Concentrator Punch-Down Block Without a Patch Panel VCN Access Point Rear Panel Installing the VCN Access Concentrator Repeat through for up to 24 telephone lines Cable Kit Access Concentrator 19-inch rack. in the 19-inch RackVCN Access Concentrator Accessory Set Part Quantity Fitting a Bracket for Rack Mounting Back Panel Connections Displays the rack after it has been wire connected Front Panel Connections Is P Pin Assignment for the RJ-21 Connector Line Cards in the VCN Access ConcentratorPatch Panel blocks at the back with RJ-21 connectors VCN AC Port No First Pin Second Pin Female RJ-21 Connector VCN Access Concentrator Unit Installed Without a Patch Panel Sequence of Configuration Inserting MAC Addresses for VCN Access Concentrator PortsGeneral guidance is provided for non-SuperStack switches Installing the VCN Access Concentrator VCN AC Port and VCN AP MAC Addresses Port No. MAC Address Installing the VCN Access Concentrator Automated Procedures for SuperStack II 1100/3300 ConfApp screen appears Figure ConfApp Screen Entering the Switch Address Community Parameter Removing Wrong Address Powering Up Ethernet SwitchVCN Access SPE-3, SPT-3, G, W Troubleshooting Installing the VCN Access Concentrator This chapter describes the following Real Time LEDIndications Status of each line in the VCN AC Using ManagementTerminal for Local Central Management Connecting the PC To connect the PC to the LMA port Terminal Emulator Type your password and press Enter LoginType your Login ID and press Enter Line CardThis section describes local management Line Card Main Menu Line Card Menu Hierarchy and Summary Line Card Menu Structure Line Card Main Menu of Port Number Sequence Corresponding to Submenus LC Version Press Enter to return to the Line Card Main Menu Management Menu Ethernet Menu Ethernet Traffic Counters Ethernet Menu Options Feature How to useEthernet Menu options are described in Table Ethernet Menu Options Ethernet Status Typical Ethernet Traffic Counters Screen Reset Ethernet Counters Change Ethernet Work Mode Menu Setting Internal Loopback Mode When you discard the operation, the message appears Setting Normal Mode Hdlc Menu options are described in Table Hdlc Menu Options Feature How to useHdlc Menu Hdlc Traffic counters Hdlc Status Reset Hdlc Counters Change Hdlc Work Mode Normal mode is lack of loopbacks Vdsl Control Menu To check the Vdsl parameters SNR, signal to noise ratio Reset All Counters Reset the Line Card Login message appears LC Configuration Menu Set Vlan ID for Management Respond by entering your new password. The message appears Set Ethernet Half/Full Duplex ModeChange Password After any number the user enters, the message appears Set to Factory Defaults Through the LMATo download new software perform the following steps Type S the downloading message in appears Procomm Plus window shown in , select Data Send File Figure Procomm Plus Terminal Screen Sending File Using Ascii Screen Procom Plus Data Send File Menu Status Screen File Downloaded Messages Software Execution Messages Line Card Management This section describes central management LMA Access for Central Management Login Process Central Management Menus in the LMA Interface Login Process Central Management Menu Hierarchy and Summary Central Management Menu Structure VCN Access Concentrator Menu Central Management Menus and Corresponding Number Sequence To access central management Management Agent MenuLine Card Main Menu for Line Card Version Information Slot 1 Line Card Main Menu Monitoring Menu Hardware and Software Version Brief Status of All Ports Monitoring Menu Detailed Port Status Refresh Brief Status or View Port Statistical Detail Traffic Counters for Selected Port Select Traffic Counters and Port Dialog in appears Vdsl Information for Selected Port Vdsl Information for Selected Port Reset Port Control MenuChange Port Selection in Control Menu If you type N, the message appears If you type y, the following message appears Vdsl Restart This is followed by the messages in and , Login promptMessages in appear To abort type n and press Enter Concentrator Configuration Menu Type n and press Enter to abort Change Vlan ID for Management Change Ethernet Half or Full Duplex Mode Type 2 and press Enter the following dialog appears Change the Concentrator Password Type your new password and press Enter. The message appearsAgent Configuration Menu IP Menu IP Menu Close Telnet Session Save changes, type y and press Enter Messages appearDiscard changes, type n and press Enter n If a Telnet session exists, the message appears Default is n Set Factory Defaults To proceed, type y and press Enter the message appears Reset AgentTo reject, type n and press Enter the message appears Overview Telnet Connection Structure of Remote Menus Telnet Menu Structure Central Management Menus and Corresponding Number Sequence Telnet Login VCN Access Concentrator Hardware and Software Version To configure VCN AC management, type 5 in the VCN Access Menu appears Exiting the Telnet Management Session To terminate, type y and press Enter the message appearsTelnet session is closed Download Procedure Downloading Software to the LCs in the VCN AC VCN Service Switch 10 Front Pane VCN AP Main Menu VCN AP Software Download Menu Enter the AC Vlan ID and press Enter. The message appears LC Downloading State Table LC Downloading Results Downloading Software to VCN APs Enter the AP Vlan ID and press Enter. The message appears AP Downloading State Table Check Software Download for the LC Cards Check the following Software version of the failed LCs Download Failed for all LCs and all VCN APsDownload Failed for One or More Line Cards but not All Check the physical path between the downloading VCN AP Download Failed for One or More VCN APs but not All Managing the VCN Access Concentrator Line Power State Indicator LEDs Using Front PanelProblems LEDs to Solve Ethernet Traffic Counters Hdlc Traffic Count Indicators Error message Significance User Action From Traffic Counts Frame countsFatal Telnet Connection Problems Telnet Connection Problems Troubleshooting Product Specification Product Specification Terminal Emulation Settings Procomm Plus Terminal screen in appears Procomm Plus Settings Number From Left Function Settings Setup window opens 137 Select System Tab Parity None Flow control139 Terminal Emulation Settings Services Online Technical Hours a day, 7 days a week Access by Analog ModemUsername anonymous Country Data Rate Telephone Number Access by Digital Modem 847 262408 727 Europe, South Africa, and Middle East Country Telephone Number Asia, Pacific Rim Country Telephone Number Fax Number Page Glossary Mbaud MbpsMiniDIN Glossary Glossary Index Numbers Remote software download Requirements Vlan ID Index 3Com Corporation Limited Warranty Governing LAW EMC Statements