Safety, Mechanical, Emc | Advantech INTRAC-305 instruction

1

INTRAC-305

SAFETY

Facilities exist at the Motor Drive Cabinet for the connection of external emergency stop switches. It is highly recommended that those fitted be of the latching type.

MECHANICAL

Mounting The INTRAC-305 must not be mounted so that it is supported only by the front panel. A proper rack mounting kit must be used. This may be either of the fixed mounting type or the sliding rail type.

EMC

The unit is designed to meet the requirements of the EC EMC Directive and conforms to the relevant standards for EMC emissions and immunity.

Important To ensure that an INTRAC installation also complies with the EMC Directive it is important to make all interconnections between the INTRAC-305 and associated equipment using good quality screened cables as recommended in the appropriate sections of this manual.

© 2011 Advantech Wireless

INTRAC-305 MANUAL - Issue 3.2

Page 11

Image 11

Advantech INTRAC-305 user manual Safety, Mechanical, Emc

Contents

Preface INTRAC-305 Manual Sections PrefacePreface INTRAC-305 Subject Contents INTRAC-305 Installation Contents Introduction INTRAC-305 Introducing the INTRAC-305 Retro Fitting Introduction Iquick Start Guide INTRAC-305 Quick Start Guide Do not Place in Normal Garbage or in a Fire SafetySafety INTRAC-305 Electrical EMC SafetyMechanical Page Required Mechanical Characteristics of the Antenna System Specification & OptionsSpecification & Options Specification & Options INTRAC-305 Specification Do not Mount by Front Panel Lugs Alone Serial Interfaces Voltage INTRAC-305 Deliberately blank Front Panel Operating the INTRAC-305Operation Menu Structure Operation INTRAC-305 Enter System SetupFunction Next Field Alphabetical Index of Menus INTRAC-305 Home Home Standby Standby Goto Auto Continue New Model NEW Mode MANUAL/STOW Home NEW Mode Menu KEY Goto Position Search Operation Goto Satellite Auto Continue Auto NEW Model Switched OFF Function ConfigurationWhen IT is Required to Control the Intrac from Remote Terminal Diagnostics Must be Home Function Menu KEY 6 Enter Beacon Frequency Home Function Menu KEY 6 X2 Enter Config Menu KEY 6 X2 EnterEdit Satellite Table Soft Limits Drive in Manual Mode is not Inhibited bySoft Limits X2 Resolver Setup X2 Setup Diagnostics On Diagnostics on / Diagnostics OFF Beacon Threshold Contrast & Brightness Home Function System Setup EnterSystem Setup Enter Fine Tune sense Home Function System Setup Azimuth true Elevation inv Fine Tune Offsets Station CO-ORDINATES Date & Time Time Rate Correction AZ & EL Beamwidth Stow Setup Used Select Stow USE Fitted Options Models Enter Rapid Model GenerateHome Function Models Enter Models Menu KEY 6 Enter Program TrackHome Function Models Menu KEY 6 Enter Home Function Models Reserve Model INTRAC-305EDIT IESS-412 Edit Norad Buffer Edit Star Track Edit Satellite Table Intrac IESS-412 Clear Models More Show Alarms REMOTE/LOCAL Normal Operation Primary Alarms Alarms & ErrorsAlarms & Errors Recovering from Alarms Alarms & Errors INTRAC-305Secondary Alarms Alarm Outputs IESS-412 Data INTRAC-305 Alarms & ErrorsErrors Power Failure Deliberately blank Technical Description Technical Description Technical Description INTRAC-305 Modes Technical Description Auto normal operating mode High accuracy of the model the tracking is within 0.05dB 72hrs, the beacon is still not producing a useful signal*Using either IESS-412 or Norad data. see Reserve Model Where the satellite’s position is only roughly known search During those scans and phase two of the search is Enters Standby. The antenna can then be peaked usingManual mode or search mode see below before selecting Manually or in search mode see below. To commence Using IESS-412 or Norad Data LMO value is given in the range -180to +180. Than two places of decimals Bstar EpochXNDT20 XNDD60 Antenna Motion Limits Axes Position Tracking Signal Technical Description INTRAC-305 Installation Installation Connections general Installation INTRAC-305 Rear Panel Layout InstallationConnections Block Diagram Intractm 305 Resolvers Connector Connector PIN Allocations Motor Control Signals to the Motor Drive Cabinet Remote Port Stp-Trk Inputs / Alarm outputsCommunication Ports Test Port 1 & 2 RS422 Test Port 1 & 2 RS423 Second PC connected to Test Port Data can be monitored during remote operation by using a INTRAC-305 Installation Tracking signal may be provided as a dc voltage from an Tracking Signal Input Manual Operation Emergency Stop switch is releasedAppropriate drive command re-instated Operational Checks Auto Operation Remote Control Fault Finding Fault Finding Intrac doesn’t appear Fault Finding INTRAC-305Fault Symptoms To power up TWO Part Retaining PIN Pressing the switch opens both sets of contacts. The switch System Alarm indicator to illuminate and the Intrac toEnter Standby Mode Switch consists of two normally closed N.C. contacts Example No Antenna Drive Fault Finding INTRAC-305 Repair Service Warranty & RepairWarranty & Repair Warranty Contract AMT Limited will investigate the fault, determine the mostEffective repair technique and issue a repair cost estimate Customer either by a Purchase Order or through a Repair