Time Rate Correction | Advantech INTRAC-305 manual

3

INTRAC-305

OPERATION

TIME RATE CORRECTION

Current Mode		Tracking
Control State		Local
Beac Freq		11.452000 GHz
Beac Level		-10.05	dB
El	Angle	25.37o
Az	Angle	210.50o
Pol	Angle	27.4 o

Seconds/Day: 045

Press EN to accept selection

Function

Standby

Home

Models

Config

System

Setup

1

2

3

4

5

6

puts the antenna control system into STANDBY mode and skips to the HOME menu

skips to the Home (root) menu

skips to the Models menu

skips to the Config menu

skips to the System Setup menu

(not used)

Path	HOME - FUNCTION - SYSTEM SETUP -
	MENU KEY 6 (x3) - ENTER - MENU KEY 3
Description	Allows the time keeping accuracy of the clock to be adjusted.
	The adjustment is in the range from minus 180 seconds per
	day to plus 180 seconds per day,
	Use the Numeric Keypad to enter the value. The +/- key is
	used to set gain or loss.
	Pressing ENTER accepts the displayed value.
Note	Changing the Time Rate Correction value does not affect the
	orbit model.

© 2011 Advantech Wireless

INTRAC-305 MANUAL - Issue 3.2

Page 33

Image 45

Advantech INTRAC-305 user manual Time Rate Correction

Contents

Preface INTRAC-305 Preface PrefaceManual Sections INTRAC-305 Subject Contents INTRAC-305 Installation Contents Introduction INTRAC-305 Introducing the INTRAC-305 Retro Fitting Introduction Iquick Start Guide INTRAC-305 Quick Start Guide Safety INTRAC-305 SafetyElectrical Do not Place in Normal Garbage or in a Fire Safety MechanicalEMC Page Specification & Options Specification & OptionsRequired Mechanical Characteristics of the Antenna System Specification & Options INTRAC-305 Specification Do not Mount by Front Panel Lugs Alone Serial Interfaces Voltage INTRAC-305 Deliberately blank Operating the INTRAC-305 OperationFront Panel Menu Structure Operation INTRAC-305 Function System SetupNext Field Enter Alphabetical Index of Menus INTRAC-305 Home Home Standby Standby Goto Auto Continue New Model NEW Mode MANUAL/STOW Home NEW Mode Menu KEY Goto Position Search Operation Goto Satellite Auto Continue Auto NEW Model When IT is Required to Control the Intrac from Function ConfigurationRemote Terminal Diagnostics Must be Switched OFF Home Function Menu KEY 6 Enter Beacon Frequency Config Menu KEY 6 X2 Enter Edit Satellite TableHome Function Menu KEY 6 X2 Enter Drive in Manual Mode is not Inhibited by Soft LimitsSoft Limits X2 Resolver Setup X2 Setup Diagnostics On Diagnostics on / Diagnostics OFF Beacon Threshold Home Function System Setup Enter System Setup EnterContrast & Brightness Fine Tune sense Home Function System Setup Azimuth true Elevation inv Fine Tune Offsets Station CO-ORDINATES Date & Time Time Rate Correction AZ & EL Beamwidth Stow Setup Used Select Stow USE Fitted Options Rapid Model Generate Home Function Models EnterModels Enter Program Track Home Function Models Menu KEY 6 EnterModels Menu KEY 6 Enter Home Function Models Reserve Model INTRAC-305EDIT IESS-412 Edit Norad Buffer Edit Star Track Edit Satellite Table Intrac IESS-412 Clear Models More Show Alarms REMOTE/LOCAL Normal Operation Alarms & Errors Alarms & ErrorsPrimary Alarms Secondary Alarms Alarms & Errors INTRAC-305Alarm Outputs Recovering from Alarms Errors INTRAC-305 Alarms & ErrorsPower Failure IESS-412 Data Deliberately blank Technical Description Technical Description Technical Description INTRAC-305 Modes Technical Description Auto normal operating mode Using either IESS-412 or Norad data. see Reserve Model 72hrs, the beacon is still not producing a useful signal*Where the satellite’s position is only roughly known search High accuracy of the model the tracking is within 0.05dB Manual mode or search mode see below before selecting Enters Standby. The antenna can then be peaked usingManually or in search mode see below. To commence During those scans and phase two of the search is Using IESS-412 or Norad Data LMO value is given in the range -180to +180. Than two places of decimals XNDT20 EpochXNDD60 Bstar Antenna Motion Limits Axes Position Tracking Signal Technical Description INTRAC-305 Installation Installation Connections general Installation INTRAC-305 Installation Connections Block DiagramRear Panel Layout Intractm 305 Resolvers Connector Connector PIN Allocations Motor Control Signals to the Motor Drive Cabinet Stp-Trk Inputs / Alarm outputs Communication PortsRemote Port Test Port 1 & 2 RS422 Test Port 1 & 2 RS423 Second PC connected to Test Port Data can be monitored during remote operation by using a INTRAC-305 Installation Tracking signal may be provided as a dc voltage from an Tracking Signal Input Appropriate drive command re-instated Emergency Stop switch is releasedOperational Checks Manual Operation Auto Operation Remote Control Fault Finding Fault Finding Fault Symptoms Fault Finding INTRAC-305To power up Intrac doesn’t appear TWO Part Retaining PIN Enter Standby Mode System Alarm indicator to illuminate and the Intrac toSwitch consists of two normally closed N.C. contacts Pressing the switch opens both sets of contacts. The switch Example No Antenna Drive Fault Finding INTRAC-305 Warranty & Repair Warranty & RepairWarranty Repair Service Effective repair technique and issue a repair cost estimate AMT Limited will investigate the fault, determine the mostCustomer either by a Purchase Order or through a Repair Contract