Connector PIN Allocations | Advantech INTRAC-305 manual

INSTALLATION

INTRAC-305

CONNECTOR PIN ALLOCATIONS

Resolvers	The Az, El and Pol resolvers connect to the 50 way resolver
	connector.

INTRACTM 305 Resolvers

Connector

50 Way D Type Plug

Signal Name

1

Hi Sin Az

34Lo Sin Az

35Hi Cos Az

19	Lo Cos Az
47	Hi Ref Az
31	Lo Ref Az
39	Hi Sin El

23Lo Sin El

24Hi Cos El

8	Lo Cos El
32	Hi Ref El
16	Lo Ref El
28	Hi Sin Pol

12Lo Sin Pol

13Hi Cos Pol

46	Lo Cos Pol
17	Hi Ref Pol
50	Lo Ref Pol

Note	All other pins of the 50 way connector are unused

Page 68

INTRAC-305 MANUAL - Issue 3.2

©2011 Advantech Wireless

Image 80

Advantech INTRAC-305 user manual Connector PIN Allocations, Intractm 305 Resolvers Connector

Contents

INTRAC-305 Preface Manual Sections PrefacePreface INTRAC-305 Contents INTRAC-305 Subject Contents Installation Introducing the INTRAC-305 Introduction INTRAC-305 Introduction Retro Fitting Iquick Start Guide INTRAC-305 Quick Start Guide Safety Safety INTRAC-305Electrical Do not Place in Normal Garbage or in a Fire EMC SafetyMechanical Page Required Mechanical Characteristics of the Antenna System Specification & OptionsSpecification & Options Specification Specification & Options INTRAC-305 Do not Mount by Front Panel Lugs Alone Voltage Serial Interfaces INTRAC-305 Deliberately blank Front Panel Operating the INTRAC-305Operation Operation INTRAC-305 Menu Structure System Setup FunctionNext Field Enter Alphabetical Index of Menus INTRAC-305 Home Home Standby Standby NEW Mode Goto Auto Continue New Model Home NEW Mode Menu KEY MANUAL/STOW Goto Position Operation Search Goto Satellite Auto Continue Auto NEW Model Function Configuration When IT is Required to Control the Intrac fromRemote Terminal Diagnostics Must be Switched OFF Beacon Frequency Home Function Menu KEY 6 Enter Home Function Menu KEY 6 X2 Enter Config Menu KEY 6 X2 EnterEdit Satellite Table Soft Limits Drive in Manual Mode is not Inhibited bySoft Limits X2 Setup X2 Resolver Setup Diagnostics on / Diagnostics OFF Diagnostics On Beacon Threshold Contrast & Brightness Home Function System Setup EnterSystem Setup Enter Home Function System Setup Fine Tune sense Fine Tune Offsets Azimuth true Elevation inv Station CO-ORDINATES Date & Time Time Rate Correction AZ & EL Beamwidth Stow Setup Select Stow USE Used Fitted Options Models Enter Rapid Model GenerateHome Function Models Enter Models Menu KEY 6 Enter Program TrackHome Function Models Menu KEY 6 Enter Reserve Model Home Function Models INTRAC-305EDIT IESS-412 Edit Norad Buffer Edit Star Track Edit Satellite Table Clear Models Intrac IESS-412 Show Alarms More REMOTE/LOCAL Normal Operation Primary Alarms Alarms & ErrorsAlarms & Errors Alarms & Errors INTRAC-305 Secondary AlarmsAlarm Outputs Recovering from Alarms INTRAC-305 Alarms & Errors ErrorsPower Failure IESS-412 Data Deliberately blank Technical Description Technical Description Technical Description INTRAC-305 Modes Auto normal operating mode Technical Description 72hrs, the beacon is still not producing a useful signal* Using either IESS-412 or Norad data. see Reserve ModelWhere the satellite’s position is only roughly known search High accuracy of the model the tracking is within 0.05dB Enters Standby. The antenna can then be peaked using Manual mode or search mode see below before selectingManually or in search mode see below. To commence During those scans and phase two of the search is Using IESS-412 or Norad Data Than two places of decimals LMO value is given in the range -180to +180. Epoch XNDT20XNDD60 Bstar Antenna Motion Limits Tracking Signal Axes Position Technical Description INTRAC-305 Installation Installation Installation INTRAC-305 Connections general Rear Panel Layout InstallationConnections Block Diagram Connector PIN Allocations Intractm 305 Resolvers Connector Signals to the Motor Drive Cabinet Motor Control Remote Port Stp-Trk Inputs / Alarm outputsCommunication Ports Test Port 1 & 2 RS423 Test Port 1 & 2 RS422 Data can be monitored during remote operation by using a Second PC connected to Test Port INTRAC-305 Installation Tracking Signal Input Tracking signal may be provided as a dc voltage from an Emergency Stop switch is released Appropriate drive command re-instatedOperational Checks Manual Operation Remote Control Auto Operation Fault Finding Fault Finding Fault Finding INTRAC-305 Fault SymptomsTo power up Intrac doesn’t appear TWO Part Retaining PIN System Alarm indicator to illuminate and the Intrac to Enter Standby ModeSwitch consists of two normally closed N.C. contacts Pressing the switch opens both sets of contacts. The switch No Antenna Drive Example Fault Finding INTRAC-305 Warranty & Repair Warranty & RepairWarranty Repair Service AMT Limited will investigate the fault, determine the most Effective repair technique and issue a repair cost estimateCustomer either by a Purchase Order or through a Repair Contract