Installation, Connections Block Diagram | Advantech INTRAC-305

INTRAC-305

Connections Block Diagram

MOTOR

CONTROLLER

MOTOR

CABINET CONTROL

BEACON

INTRAC-305

ALARM

REMOTE

TERMINAL

6

INSTALLATION

AZ

RESOLVER

EL

RESOLVER

POL

RESOLVER

All connections to the INTRAC-305 are made via its rear panel. The following connectors are available :-

Remote Port (I/O)	25-way D-type	plug
Test Ports 1 & 2 (I/O)	9-way D-type	plugs
Resolver I/P	50-way D-type	plug
Motor Controls Output	50-way D-type	socket
Steptrack I/P	25-way D-type	plug
Beacon Signal I/P	N-type (L-band)	socket
Power I/P	3 pin IEC	plug

Rear Panel Layout

Note: On Dual PSU units the single fused power inlet is replaced by two switched power inlets.

© 2011 Advantech Wireless

INTRAC-305 MANUAL - Issue 3.2

Page 67

Image 79

Advantech INTRAC-305 user manual Installation, Connections Block Diagram, Rear Panel Layout

Contents

Preface INTRAC-305 Preface PrefaceManual Sections INTRAC-305 Subject Contents INTRAC-305 Installation Contents Introduction INTRAC-305 Introducing the INTRAC-305 Retro Fitting Introduction Iquick Start Guide INTRAC-305 Quick Start Guide Do not Place in Normal Garbage or in a Fire SafetySafety INTRAC-305 Electrical Mechanical SafetyEMC Page Specification & Options Specification & OptionsRequired Mechanical Characteristics of the Antenna System Specification & Options INTRAC-305 Specification Do not Mount by Front Panel Lugs Alone Serial Interfaces Voltage INTRAC-305 Deliberately blank Operation Operating the INTRAC-305Front Panel Menu Structure Operation INTRAC-305 Enter System SetupFunction Next Field Alphabetical Index of Menus INTRAC-305 Home Home Standby Standby Goto Auto Continue New Model NEW Mode MANUAL/STOW Home NEW Mode Menu KEY Goto Position Search Operation Goto Satellite Auto Continue Auto NEW Model Switched OFF Function ConfigurationWhen IT is Required to Control the Intrac from Remote Terminal Diagnostics Must be Home Function Menu KEY 6 Enter Beacon Frequency Edit Satellite Table Config Menu KEY 6 X2 EnterHome Function Menu KEY 6 X2 Enter Soft Limits Drive in Manual Mode is not Inhibited bySoft Limits X2 Resolver Setup X2 Setup Diagnostics On Diagnostics on / Diagnostics OFF Beacon Threshold System Setup Enter Home Function System Setup EnterContrast & Brightness Fine Tune sense Home Function System Setup Azimuth true Elevation inv Fine Tune Offsets Station CO-ORDINATES Date & Time Time Rate Correction AZ & EL Beamwidth Stow Setup Used Select Stow USE Fitted Options Home Function Models Enter Rapid Model GenerateModels Enter Home Function Models Menu KEY 6 Enter Program TrackModels Menu KEY 6 Enter Home Function Models Reserve Model INTRAC-305EDIT IESS-412 Edit Norad Buffer Edit Star Track Edit Satellite Table Intrac IESS-412 Clear Models More Show Alarms REMOTE/LOCAL Normal Operation Alarms & Errors Alarms & ErrorsPrimary Alarms Recovering from Alarms Alarms & Errors INTRAC-305Secondary Alarms Alarm Outputs IESS-412 Data INTRAC-305 Alarms & ErrorsErrors Power Failure Deliberately blank Technical Description Technical Description Technical Description INTRAC-305 Modes Technical Description Auto normal operating mode High accuracy of the model the tracking is within 0.05dB 72hrs, the beacon is still not producing a useful signal*Using either IESS-412 or Norad data. see Reserve Model Where the satellite’s position is only roughly known search During those scans and phase two of the search is Enters Standby. The antenna can then be peaked usingManual mode or search mode see below before selecting Manually or in search mode see below. To commence Using IESS-412 or Norad Data LMO value is given in the range -180to +180. Than two places of decimals Bstar EpochXNDT20 XNDD60 Antenna Motion Limits Axes Position Tracking Signal Technical Description INTRAC-305 Installation Installation Connections general Installation INTRAC-305 Connections Block Diagram InstallationRear Panel Layout Intractm 305 Resolvers Connector Connector PIN Allocations Motor Control Signals to the Motor Drive Cabinet Communication Ports Stp-Trk Inputs / Alarm outputsRemote Port Test Port 1 & 2 RS422 Test Port 1 & 2 RS423 Second PC connected to Test Port Data can be monitored during remote operation by using a INTRAC-305 Installation Tracking signal may be provided as a dc voltage from an Tracking Signal Input Manual Operation Emergency Stop switch is releasedAppropriate drive command re-instated Operational Checks Auto Operation Remote Control Fault Finding Fault Finding Intrac doesn’t appear Fault Finding INTRAC-305Fault Symptoms To power up TWO Part Retaining PIN Pressing the switch opens both sets of contacts. The switch System Alarm indicator to illuminate and the Intrac toEnter Standby Mode Switch consists of two normally closed N.C. contacts Example No Antenna Drive Fault Finding INTRAC-305 Repair Service Warranty & RepairWarranty & Repair Warranty Contract AMT Limited will investigate the fault, determine the mostEffective repair technique and issue a repair cost estimate Customer either by a Purchase Order or through a Repair