Manuals / Allied Telesis / Computer Equipment / Switch

Allied Telesis AT-X510DP-52GTX manual Preface

Models: AT-X510DP-52GTX

1 129

Download 129 pages 55.29 Kb

Troubleshooting Specifications Install Pin MDI Signal MDI-X Signal Connecting the AC Power Cord Setting the Priority Numbers Reviewing Safety Precautions Safety Power Supply Modules Features

Page 14

Image 14

Preface

14

Page 13 Page 15

Page 14

Image 14

Allied Telesis AT-X510DP-52GTX manual Preface

Page 13 Page 15

Related pages What audio modes are compatible with SRS TS HD technology? Check the details here.

Contents

Installation Guide Page Electrical Safety and Emissions Standards Translated Safety Statements Contents Powering On the Switches Individually Figures Figures Tables Tables Preface Document Conventions Contacting Allied Telesis Preface Overview Chapter Features 10/100/1000 Mbps Twisted Pair Ports SFP+ Slots Power Supply Modules Front Panel of the AT-x510DP-52GTX Switch Front and Rear Panels Management Panel AT-x510DP-52GTX Management Panel Speed Duplex Mode Wiring Configuration 10/100/1000Base-T Twisted Pair Ports Maximum Distance Cable Requirements Port Pinouts SFP+ Slots Stacking SFP+ Slots Eco-friendly Button LEDs LEDs for the Twisted Pair Ports LEDs for SFP+ Slots LEDs for the Stacking Slots ID LED Switch ID LEDs in the Low Power Mode USB Port Console Port Power Supplies AT-PWR100R AC Power Supply Overview Virtual Chassis Stacking Overview Stacking Slots Stacking Transceivers Stacking Cable Type Operating Distance X510DP-52GTX Installation Guide Stacking Port Topologies Stack in on page 41 has four switches in the linear topology Stack of Two Switches in the Ring Topology 2697 Master and Member Switches Selection of the Master Switch X510DP-52GTX Installation Guide Specifying Ports in the Command Line Interface Port1.0.n Beginning the Installation Reviewing Safety Precautions X510 Series Installation Guide for Virtual Chassis Stacking Beginning the Installation X510 Series Installation Guide for Virtual Chassis Stacking Choosing a Site for the Switches Planning a Stack Operating Distances of the AT-StackOP/0.3 Transceiver Unpacking the Switch Beginning the Installation Installing the Switch and its Power Supplies Installing the Power Cord Retaining Clip Installing Power Supply Modules Overview Installing a Power Supply Installing the Switch and its Power Supplies Securing the AT-PWR100R Power Supply Module PWR100R Installing the Switches on a Table or Desktop Installing the Switch in an Equipment Rack Turning the Switch Upside Down Attaching the Equipment Rack Brackets Mounting the Switch Horizontally in an Equipment Rack Connecting AC Power to a Power Supply Module Connecting the AC Power Cord Installing the Switch and its Power Supplies Power Wiring to a DC AT-PWR250R-80 Power Supply Module +48 VDC Positive Ground VDC Negative Terminal Inserting Wires into a DC Terminal Block Installing the Switch and its Power Supplies Starting a Local Management Session Switch Initialization Messages Monitoring the Initialization Processes Switch Initialization Messages Switch Initialization Messages Configuring the Switch for Stand-alone Operations Configuring the Switch for Stand-alone Operations Disabling VCStack No stack id enable Awplusconfig# no stack 1 enable Confirming Status VCStack Feature Status of a Stacking Slot When VCStack is Enabled Port1.0.n Configuring the Switch for Stand-alone Operations Verifying the Status of VCStack and Activating VCStack Verifying the Status of VCStack Activating the VCStack Feature Activating VCStack Awplusconfig# exit awplus# Awplus# reboot reboot system? y/n awplus# Verifying the Status of VCStack and Activating VCStack Cabling the Stacking Ports Cabling Switches with AT-StackXS/1.0 Transceivers Removing the Dust Cover from the AT-StackXS/1.0 Transceiver Installing the AT-StackXS/1.0 Transceiver in Slot S1 SFP+ CON 2685 Handle on the AT-StackOP/0.3 and AT-StackOP/9.0 Transceivers Installing the AT-StackOP/0.3 or AT-StackOP/9.0 Transceiver Positioning the Handle in the Upright Position 2691 Powering On the Stack Plus Operating System for x510 Series Powering On the Switches Individually 103 Powering On the Switches Simultaneously 105 Verifying the Stack Awplus show stack Setting the Priority Numbers Awplus# write Building configuration Cabling the Networking Ports Cabling the Twisted Pair Ports 111 Installing SFP and SFP+ Transceivers On page 113 shows the dust plug being removed from a port Removing the Dust Cover from an SFP or SFP+ Transceiver 2678 Cabling the Networking Ports 116 Troubleshooting Try inserting the PSU into the other PSU bay 118 119 120 121 Troubleshooting 122 Environmental Specifications Technical SpecificationsPhysical Specifications Appendix a Power Specifications Certifications Pin MDI Signal MDI-X Signal RJ-45 Twisted Pair Port Pinouts Pinout Pair Pin Signal RJ-45 Style Serial Console Port Pinouts 128 129