Bosch Appliances TTCAN specification

TTCAN

User’s Manual

Revision 1.6

Copyright Notice and Proprietary Information

Copyright © 1998, 1999, 2002 Robert Bosch GmbH. All rights reserved. This software and manual are owned by Robert Bosch GmbH, and may be used only as authorized in the license agreement controlling such use. No part of this publication may be reproduced, transmitted, or translated, in any form or by any means, electronic, mechanical, manual, optical, or otherwise, without prior written permission of Robert Bosch GmbH, or as expressly provided by the license agreement.

Disclaimer

ROBERT BOSCH GMBH MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

ROBERT BOSCH GMBH RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO THE PRODUCTS DESCRIBED HEREIN. ROBERT BOSCH GMBH DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN.

manual_about.fm

BOSCH

- 2/77 -

11.11.02

Image 2

Bosch Appliances TTCAN user manual Copyright Notice and Proprietary Information

Contents

User’s Manual Robert Bosch GmbH Copyright Notice and Proprietary Information Conventions Scope References Terms and Abbreviations Functional Overview 2.2. Block Diagram Operating ModesChange Control Can Application Ttcan Message Handling Ttcan ConfigurationTtcan Schedule Initialisation List of Figures Conventions Change Control Current StatusChange History Helvetica bold Term Meaning Functional Overview Cpuifc Ttcan Operating Modes Software Initialisation Can Message Transfer Test Register addresses 0x0B & 0x0A Disabled Automatic RetransmissionTest Mode Ttcan =1 Loop Back Mode Loop Back combined with Silent Mode No Message RAM Mode Software control of Pin Cantx Address Name Reset Value Hardware Reset Description Ttcan Register Summary EIE CCEDAR SIE No Error Status Register addresses 0x03 Bit Timing Register addresses 0x07 Error Counter addresses 0x05Status Interrupts BRP Extension Register addresses 0x0D & 0x0C Arb IFx Command Mask RegistersDirection = Write Control IFx Command Request RegistersDirection = Read ClrIntPnd IFx Message Buffer Registers BusyMessage Number IFx Mask Registers Message Object in the Message Memory IFx Message Control RegistersIFx Data a and Data B Registers Xtd ID28-0Msk28-0 Dir 26/77 11.11.02 Message Handler Registers Interrupt Register addresses 0x09 Interrupt Pending Registers Transmission Request RegistersNew Data Registers Trigger Number 2 IF1 Data B1 and B2 Registers for Trigger Memory AccessMessage Valid 1 Register TimeMark At CycleCount mod TT Operation Mode Register addresses 0x29Type MPr2-0 TEW EecsRdlc Bark TT Interrupt Enable Register addresses 0x31CCM AppWdL GTW CELGTE SWE RTO TUR Numerator Conﬁguration Low Register addresses 0x57 TT Error Level Register addresses 0x3F & 0x3ETT Cycle Count Register addresses 0x3D & 0x3C TT StopWatch Register addresses 0x61 TUR Denominator Conﬁguration Register addresses 0x59TUR Numerator Actual Registers addresses 0x5B & 0x5A Ecal QCSQgtp Egtf ECS TMCDET SWS EPE TMG 40/77 11.11.02 Internal can Message Handling Data Transfer Between IFx Registers and Message RAM Transmission of Messages in Event Driven can Communication Start Reception of Remote Frame Acceptance Filtering of Received MessagesReception of Data Frame Storing Received Messages in Fifo Buffers Receive / Transmit Priority Conﬁguration of the Module Bit Time and Bit Rate Sync PropSeg PhaseSeg1 PhaseSeg21 Conﬁguration of the Bit Timing Canclk input Nominal can Bit Time Propagation Time Segment BRP Phase Buffer Segments and Synchronisation Synchronisation on late and early Edges Filtering of Short Dominant Spikes Oscillator Tolerance Range 1.5 Conﬁguration of the can Protocol Controller Calculation of the Bit Timing Parameters Example for Bit Timing at high Baudrate Example for Bit Timing at low Baudrate 2 Conﬁguration of the Message Memory 2.1 Conﬁguration of a Transmit Object for Data Frames 2.2 Conﬁguration of a Single Receive Object for Data Frames 2.3 Conﬁguration of a Fifo Buffer Can Communication Handling of Interrupts Updating a Transmit Object Requesting New Data for a Receive Object Changing a Transmit ObjectReading Received Messages Reading from a Fifo Buffer CPU Handling of a Fifo Buffer Interrupt Driven Ttcan Conﬁguration Ttcan Timing Message Scheduling TUR510 125000 32.5 100/12 529/17 Trigger Memory 63/77 11.11.02 Periodic Transmit Message Message ObjectsReference Message Potential Time Masters Event Driven Transmit MessageTime Slaves Periodic Messages Ttcan Message Handling Message ReceptionMessage Transmission Event Driven Messages Ttcan Gap Control Stopwatch Cycle Time and Global Time Synchronisation Ttcan Interrupt and Error Handling Previous RefMark Conﬁguration Example Register Remark Rdlc & TEW & CCM Type & Msg & CycleCode RTO , TM , L2 , TTMode3 74/77 11.11.02 Customer Interface GenericInterface Busy = ‘1’ Busy = ‘0’ Timing of the Wait output signalCanclk Canwaitb Interrupt Timing EOF