8. ELECTRIC MECHANISM

Switch

Motion when set to ON

Initial value

Solenoid

Pneumatic

 

 

 

When using the inner clamping device, shunting to prevent interference

 

 

memo-15

between the inner clamping device and the needle is not carried out after the

--

--

 

sewing end.

 

 

memo-16

Needle cooler can be used (available by special order).

--

--

memo-17

Thread take-up device is not operated at the sewing end.

--

--

memo-18

Thread take-up device operates one stitch before the sewing end.

--

--

 

 

 

 

memo-19

For solenoid specifications, presser position errors are not detected.

--

--

memo-1A

Needle up stop position errors are not detected.

--

--

 

Work clamp can be moved up and down before the home position is detected.

 

 

memo-1b

(Normally the work clamp cannot be moved up and down until after the home

--

--

 

position has been detected.)

 

 

memo-1c

-

--

--

 

 

 

 

memo-1d

For pneumatic specifications, the air pressure detection switch is enabled.

--

--

(The air pressure sensor is a special-order option.)

 

 

 

 

Errors can be reset using the EMERGENCY STOP switch.

 

 

memo-1E

(EMERGENCY STOP switch is available as an option except for KE-434*,

--

--

 

435*, 484C.)

 

 

 

Thread is not trimmed when an emergency stop occurs during sewing.

 

 

memo-1F

(EMERGENCY STOP switch is available as an option except for KE-434*,

--

--

 

435*, 484C.)

 

 

<Memory switches 20 - 2F>

Switch

Motion when set to ON

 

Initial value

 

Solenoid

Pneumatic

 

 

 

memo-20

-

 

--

--

memo-21

Rotating-type thread breakage detector operates. (Device is available

by

--

--

special order.)

 

 

 

 

 

 

When thread breakage detection is operating, sensitivity is decreased at the

 

 

memo-22

sewing start. (Sensitivity during sewing is three stitches.)

 

--

--

 

[Rotating-type] 8→14 stitches, [Fiber-type] 5→10 stitches

 

 

 

memo-23

When DIP switch A-8 is simultaneously ON, setting values changed using the

--

--

operation panel are ignored.

 

 

 

 

 

memo-24

-

 

--

--

memo-25

-

 

--

--

memo-26

Enables the fiber-type thread breakage detector (when memo-21 is ON)

 

--

--

 

 

 

 

memo-27

Test operation of pneumatic-type thread trimmer, tension release and thread

--

--

take-up. (KE-484C)

 

 

 

 

 

memo-28

Stores the amount of parallel movement in memory.

 

--

--

(Use the memory all clear operation to clear the setting.)

 

 

 

 

 

memo-29

Pneumatic thread wiper sensor is enabled (when memo-12=ON

and

--

--

memo-14=ON) (sensor is optional). (KE-484C)

 

 

 

 

 

memo-2A

Special emergency stop release method is used (error code E-11 is cleared by

--

--

pressing reset switch once and home position is cleared). (KE-484C)

 

 

 

 

 

memo-2b

 

 

 

 

-

-

 

--

--

memo-2E

 

 

 

 

memo-2F

Pneumatic thread wiper and work clamp operate together. (KE-484C)

 

--

--

KE-430B, 430C series

152