8. ELECTRIC MECHANISM
Wait at least 5 minutes after turning off the power switch and disconnecting the power cord from the wall outlet before opening the face plate of the control box. Touching areas where high voltages are present can result in severe injury.
If a malfunction should occur with the sewing machine, a buzzer will sound and an error code will appear in the display window. Follow the remedy procedure to eliminate the cause of the problem.
REFERENCE segment LED alphabet
|
| Panel display |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Text display | A |
| b | c |
| d |
| E |
| F | G |
| H | L |
| O |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
Code |
|
| Cause |
|
|
|
|
|
|
|
| Remedy |
|
|
|
| ||
| Emergency stop switch was pressed. |
| Turn the EMERGENCY STOP switch clockwise to | |||||||||||||||
|
| release the lock, and then press the RESET switch | ||||||||||||||||
|
|
|
|
|
|
|
|
| to reset the error. |
|
|
|
|
|
| |||
|
| Emergency stop switch was pressed during |
| Turn the EMERGENCY STOP switch clockwise to | ||||||||||||||
|
| release the lock, and then press the RESET switch | ||||||||||||||||
| sewing. |
|
|
|
|
|
| to reset the error. You can then press the BOBBIN. | ||||||||||
|
|
|
|
|
|
|
| |||||||||||
|
| Emergency stop switch is being continually |
| WIND switch to repeat the sewing. |
|
|
| |||||||||||
|
| Turn off the power and check. |
|
|
|
| ||||||||||||
| pressed, or emergency switch connection |
|
|
|
|
| ||||||||||||
|
| error. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Machine specification select connector is not | Turn off the power and check if connectors P3 is |
| |||||||||||||||
| connected properly. |
|
|
|
| disconnected. |
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
| Turn the EMERGENCY STOP switch clockwise to | |||||||||
| Thread breakage detected. |
|
|
| release the lock, and then press the RESET switch | |||||||||||||
|
|
|
| to reset the error. You can then press the BOBBIN. | ||||||||||||||
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
| WIND switch to repeat the sewing. |
|
|
| ||||||
| Air pressure drop error. |
|
|
|
| Turn off the power and check. If drops in air |
| |||||||||||
|
|
|
|
| pressure are not being detected, clear all memory | |||||||||||||
|
| The foot switch was pressed or the operation | settings and then set the | |||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
| |||||||
| panel was used while the machine head was | Turn off the power, and then return the machine |
| |||||||||||||||
| tilted back, or the machine head was tilted |
| head to its original position. |
|
|
|
| |||||||||||
|
|
|
|
|
|
| ||||||||||||
|
| back while it was operating. |
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| Turn off the power, and then turn the machine pulley | |||||||||
|
| Problem with machine motor stopping, or |
| to check if the machine has locked up. Check the | ||||||||||||||
|
|
| synchronizer connection. Check if connectors P11, | |||||||||||||||
| synchronizer connection error. Or thermostat | P12 and P13 are disconnected. |
|
|
| |||||||||||||
|
| inside sewing machine motor has operated. |
| Check that the correct combination of motor and |
| |||||||||||||
|
|
|
|
|
|
|
|
| PROM has been installed. |
|
|
|
| |||||
|
|
|
|
|
|
|
|
| Check if the sewing machine motor has overheated. | |||||||||
| Machine motor operation error. |
|
|
| Turn off the power and check the ground wire |
| ||||||||||||
|
|
|
| connection. |
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| Data is outside possible sewing area due to |
| Press the RESET switch, and then set the |
| ||||||||||||||
| enlargement ratio setting. |
|
|
|
| enlargement ratio again. |
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
167 |