Document Contents | Cisco Systems PRP-1/R=, PRP-1=, PRP-2= instruction

Performance Route Processor Installation and Configuration Guide

Product Number: PRP-1=, PRP-1/R=, PRP-2=, PRP-2/R=

This hardware installation and configuration note describes the Performance Route Processor (PRP) and the PRP-2, route processors for use in Cisco 12000 Series Routers.

Document Contents

This publication includes the following sections:

•Important Information, page 2

•Product Overview, page 5

•Preparing for Installation, page 18

•Removing and Installing a PRP, page 20

•Checking the Installation, page 26

•Upgrading to the PRP, page 32

•Configuring Interfaces on the PRP, page 44

•Additional Configuration and Maintenance Tasks, page 54

Corporate Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

© 2008 Cisco Systems, Inc. All rights reserved.

Image 1

Cisco Systems PRP-1/R=, PRP-1=, PRP-2=, PRP-2/R= manual Document Contents

Contents

Document Contents Router Information Important InformationSupported Platforms PRP Redundancy Cisco IOS Software Requirements Output from a later software release would be as follows Hardware Revision Requirements Related Documentation Product Overview Shows the front panel view of the PRP-2 PRP Functions PRP Components Cisco IOS Software Storage PRP Hardware Components PRP-1 Horizontal Orientation PRP-2 Horizontal Orientation Type Size Quantity Description Location Program boot imageMB fixed Secondary CPU cache memory functions Sdram PRP LEDs Flash MemoryStatus LEDs Following LEDs are used on the PRP Display LEDs Cisco IOS System Error Messages publications Flash Disk Slots Soft Reset Switch Ethernet Ports Asynchronous Serial PortsHard Disk Drive Safety Guidelines Preparing for InstallationCompact Flash Disk Preventing Electrostatic Discharge Required Tools and Equipment Removing and Installing a PRPWorking with Electrical Equipment Removing a PRP Ejector Levers Illustrates the PRP installed in a chassis Shows the ejector levers in detail Installing a PRP Removing and Installing a PRP PRP Boot Process Checking the Installation Starting the System and Observing Initial Conditions Cisco IOS is enabled and this PRP is the active PRP Rommon for this PRP is enabled and recognized by the systemCisco IOS is enabled and this PRP is in standby mode LED Display Description Checking the Installation Checking the Installation Verifying Interface Status ETH Bits Upgrading to the PRP Router# show redundancy Upgrading to the PRP Without Rebooting the Router Router# dir disk1 Is correct, continue with Step SSO or RPR+ mode because the RPs are running the same imageAnother disk or at another location Prompted to abort the copy, type n Upgrading to the PRP Upgrading to the PRP Upgrading to the PRP Upgrading to the PRP Verify the disk contents using the dir disk1 command Upgrading to the PRP With Rebooting the Router Upgrading to the PRP Use the command upgrade rom-monitor slot rp-slot 0x10 Differentiating Between PRP-1 and PRP-2 Configuring an Ethernet Interface Configuring Interfaces on the PRPEthernet Interface Receptacles, Cables, and Pinouts RJ-45 receptacle Category 5 UTP cable with plug Crossover Cable Pinout for Connecting Two PRPs Ethernet Port Pin Signal Description Parameter RJ-45 Lists Ieee 802.3u physical characteristics for 100BASE-TXParameter Ethernet Interface Cable Connection Procedure Using the Ethernet Port on the PRP Configuring the Ethernet Interfaces Using Configuration Mode to Configure an Ethernet Interface Configuring the Console Interface Console and Auxiliary Port Connections Signal Input/Output Description Configuring the Auxiliary Interface Description of the Software Configuration Register Understanding the Software Configuration Register Additional Configuration and Maintenance Tasks Bit Number Hexadecimal Value Meaning/Function Defines the bits in the software configuration register Boot Field Meaning Boot Field SettingsDescribed in Table Command Purpose Configuring the Software Configuration Register Action/Filename Bit Bits in the Software Configuration Register Data Transmission Rate bps Address net host9600 4800 1200 2400 About Flash Disks Using Flash Disks in the PRP Product Number Removing and Installing a Flash Disk in the PRP Installing and Removing a Flash Disk Working with Flash Disks Installing a Flash Disk Boots the named file from the Flash disk in slot Booting from a Flash Disk Removing the CF from the PRP-2 Board Removing and Installing a Compact Flash Disk Removing and Installing a Hard Disk Drive Installing the Hard Disk Drive Recovering a Lost Password Initialize the router by entering the i command as follows Step Upgrading PRP Memory Locations of PRP Components and Memory GB Dimm U15 512 MB MB Dimm U15 MEM-PRP-512= MB DIMMs U15 and U18GB DIMMs U15 and U18 Cisco Product Number Dimm Modules Sdram Dimm Sockets Removing a Dimm Dimm Socket with Dual Release Levers Installing a Dimm Handling a Dimm Checking the Dimm Installation Regulatory, Compliance, and Safety Information Electromagnetic Compatibility Regulatory Statements Translated Safety Warnings and Agency ApprovalsFCC Class a Compliance Europe EU Canada Regulatory, Compliance, and Safety Information Vcci Class a Notice for Japan Class a Notice for Korea Cisco.com Obtaining DocumentationProduct Documentation DVD Cisco Product Security Overview Documentation FeedbackOrdering Documentation For emergencies only security-alert@cisco.com Reporting Security Problems in Cisco Products Obtaining Technical Assistance Product Alerts and Field NoticesCisco Technical Support & Documentation Website Submitting a Service Request Definitions of Service Request Severity Obtaining Additional Publications and Information Obtaining Additional Publications and Information OL-11656-01