Configuring Interfaces on the PRP | Cisco Systems PRP-1=, PRP-1/R=

Configuring Interfaces on the PRP

Note Field diagnostics cannot be run on the PRP-2 unless you are using software release 12.0(30)S or higher.

Note The show version command may display incorrect information for the PRP-2 card in software releases prior to 12.0(30)S.

Configuring Interfaces on the PRP

This section includes configuration and connection information for the Ethernet, console, and auxiliary interfaces on the PRP, and includes the following sections:

•Configuring an Ethernet Interface, page 44

•Configuring the Console Interface, page 51

•Configuring the Auxiliary Interface, page 53

Configuring an Ethernet Interface

PRP Ethernet interface connection and configuration information is presented in the following sections:

•Ethernet Interface Receptacles, Cables, and Pinouts, page 44

•Ethernet Interface Cable Connection Procedure, page 48

•Configuring the Ethernet Interfaces, page 49

Ethernet Interface Receptacles, Cables, and Pinouts

There are two RJ-45 Ethernet interface receptacles on the PRP and one RJ-45 Gigabit Ethernet interface receptacle on the PRP-2, providing media-dependent interface (MDI) Ethernet ports. These connections support IEEE 802.3 and IEEE 802.3u interfaces compliant with 10BASE-T and 100BASE-TX standards. The transmission speed of the Ethernet ports is auto-sensing by default and is user configurable.

	Performance Route Processor Installation and Configuration Guide
44	OL-11656-01

Image 44

Cisco Systems PRP-1=, PRP-1/R=, PRP-2=, PRP-2/R= manual Configuring Interfaces on the PRP, Configuring an Ethernet Interface

Contents

Document Contents Supported Platforms Important InformationRouter Information Cisco IOS Software Requirements PRP Redundancy Hardware Revision Requirements Output from a later software release would be as follows Product Overview Related Documentation PRP Functions Shows the front panel view of the PRP-2 PRP Components Cisco IOS Software Storage PRP Hardware Components PRP-1 Horizontal Orientation PRP-2 Horizontal Orientation MB fixed Secondary CPU cache memory functions Program boot imageType Size Quantity Description Location Sdram Flash Memory PRP LEDsStatus LEDs Following LEDs are used on the PRP Cisco IOS System Error Messages publications Display LEDs Soft Reset Switch Flash Disk Slots Hard Disk Drive Asynchronous Serial PortsEthernet Ports Compact Flash Disk Preparing for InstallationSafety Guidelines Preventing Electrostatic Discharge Working with Electrical Equipment Removing and Installing a PRPRequired Tools and Equipment Removing a PRP Illustrates the PRP installed in a chassis Ejector Levers Shows the ejector levers in detail Installing a PRP Removing and Installing a PRP Checking the Installation PRP Boot Process Starting the System and Observing Initial Conditions Rommon for this PRP is enabled and recognized by the system Cisco IOS is enabled and this PRP is the active PRPCisco IOS is enabled and this PRP is in standby mode LED Display Description Checking the Installation Checking the Installation Verifying Interface Status Upgrading to the PRP ETH Bits Upgrading to the PRP Without Rebooting the Router Router# show redundancy Router# dir disk1 SSO or RPR+ mode because the RPs are running the same image Is correct, continue with StepAnother disk or at another location Prompted to abort the copy, type n Upgrading to the PRP Upgrading to the PRP Upgrading to the PRP Upgrading to the PRP Upgrading to the PRP With Rebooting the Router Verify the disk contents using the dir disk1 command Upgrading to the PRP Use the command upgrade rom-monitor slot rp-slot Differentiating Between PRP-1 and PRP-2 0x10 Ethernet Interface Receptacles, Cables, and Pinouts Configuring Interfaces on the PRPConfiguring an Ethernet Interface RJ-45 receptacle Category 5 UTP cable with plug Ethernet Port Pin Signal Description Crossover Cable Pinout for Connecting Two PRPs Parameter Lists Ieee 802.3u physical characteristics for 100BASE-TXParameter RJ-45 Ethernet Interface Cable Connection Procedure Configuring the Ethernet Interfaces Using the Ethernet Port on the PRP Using Configuration Mode to Configure an Ethernet Interface Configuring the Console Interface Console and Auxiliary Port Connections Configuring the Auxiliary Interface Signal Input/Output Description Understanding the Software Configuration Register Description of the Software Configuration Register Additional Configuration and Maintenance Tasks Defines the bits in the software configuration register Bit Number Hexadecimal Value Meaning/Function Described in Table Boot Field SettingsBoot Field Meaning Configuring the Software Configuration Register Command Purpose Bits in the Software Configuration Register Action/Filename Bit 9600 4800 1200 2400 Address net hostData Transmission Rate bps Using Flash Disks in the PRP About Flash Disks Removing and Installing a Flash Disk in the PRP Product Number Installing and Removing a Flash Disk Installing a Flash Disk Working with Flash Disks Booting from a Flash Disk Boots the named file from the Flash disk in slot Removing and Installing a Compact Flash Disk Removing the CF from the PRP-2 Board Removing and Installing a Hard Disk Drive Installing the Hard Disk Drive Recovering a Lost Password Initialize the router by entering the i command as follows Step Upgrading PRP Memory Locations of PRP Components and Memory GB DIMMs U15 and U18 512 MB MB Dimm U15 MEM-PRP-512= MB DIMMs U15 and U18GB Dimm U15 Removing a Dimm Cisco Product Number Dimm Modules Sdram Dimm Sockets Dimm Socket with Dual Release Levers Installing a Dimm Handling a Dimm Regulatory, Compliance, and Safety Information Checking the Dimm Installation FCC Class a Compliance Translated Safety Warnings and Agency ApprovalsElectromagnetic Compatibility Regulatory Statements Canada Europe EU Regulatory, Compliance, and Safety Information Vcci Class a Notice for Japan Class a Notice for Korea Product Documentation DVD Obtaining DocumentationCisco.com Ordering Documentation Documentation FeedbackCisco Product Security Overview Reporting Security Problems in Cisco Products For emergencies only security-alert@cisco.com Cisco Technical Support & Documentation Website Product Alerts and Field NoticesObtaining Technical Assistance Submitting a Service Request Definitions of Service Request Severity Obtaining Additional Publications and Information Obtaining Additional Publications and Information OL-11656-01