Upgrading to the PRP | Cisco Systems PRP-2/R=, PRP-1=, PRP-1/R=

Upgrading to the PRP

Step 3 As soon as the “Press RETURN to get started!” message appears on the console, enter enable mode and use the upgrade rom-monitor slot rp-slotcommand. If the routine finds that an upgrade is necessary, the new code will begin to be loaded. The router will reload once the ROM monitor upgrade has completed.

Step 4 RP1 will now be active. As soon as the “Press RETURN to get started!” message appears on the console, enter enable mode and use the upgrade rom-monitor slot rp-slotcommand. If the routine finds that an upgrade is necessary, the new code will begin to be loaded. The router will reload once the ROM monitor upgrade has completed.

Step 5 RP2 will be primary now. Let the router return to full operation with IGP and EGP peers established (this may take a considerable amount of time, depending on the size and complexity of the router configuration).

Step 6 Check the line card CPU utilization using the execute-on all show proc cpu inc CPU command. If the CPU utilization has stabilized at the normal running level, proceed with the next step; otherwise, wait another five minutes and check again.

Step 7 Upgrade the Mbus-agent-rom using the upgrade mbus-agent-rom all command. Normal forwarding operation of the line cards will not be affected during the upgrade. The line cards do not need to be reloaded. If any error messages are displayed (see following example), repeat this step before contacting Cisco TAC.

MBus agent ROM upgrade failed on slot 7 (rc=5)

MBus agent ROM upgrade failed on slot 8 (rc=6)

Step 8 Use the show version command. If there is an error message at the bottom of the output indicating that a Fabric-downloader code upgrade is required, use the upgrade fabric-downloader all command. Normal forwarding operation of the line cards will not be affected during the upgrade. The line cards do not need to be reloaded. If any error messages are displayed (see following example), repeat this step before contacting Cisco TAC.

Fabric-downloader upgrade failed on slot 7 (rc=5)

Fabric-downloader upgrade failed on slot 8 (rc=6)

		Performance Route Processor Installation and Configuration Guide

	OL-11656-01			39
	OL-11656-01			39

Image 39

Cisco Systems PRP-2/R=, PRP-1=, PRP-1/R=, PRP-2= manual Upgrading to the PRP

Contents

Document Contents Important Information Router InformationSupported Platforms PRP Redundancy Cisco IOS Software Requirements Output from a later software release would be as follows Hardware Revision Requirements Related Documentation Product Overview Shows the front panel view of the PRP-2 PRP Functions PRP Components Cisco IOS Software Storage PRP Hardware Components PRP-1 Horizontal Orientation PRP-2 Horizontal Orientation Program boot image Type Size Quantity Description LocationMB fixed Secondary CPU cache memory functions Sdram Following LEDs are used on the PRP Flash MemoryPRP LEDs Status LEDs Display LEDs Cisco IOS System Error Messages publications Flash Disk Slots Soft Reset Switch Asynchronous Serial Ports Ethernet PortsHard Disk Drive Preparing for Installation Safety GuidelinesCompact Flash Disk Preventing Electrostatic Discharge Removing and Installing a PRP Required Tools and EquipmentWorking with Electrical Equipment Removing a PRP Ejector Levers Illustrates the PRP installed in a chassis Shows the ejector levers in detail Installing a PRP Removing and Installing a PRP PRP Boot Process Checking the Installation Starting the System and Observing Initial Conditions LED Display Description Rommon for this PRP is enabled and recognized by the systemCisco IOS is enabled and this PRP is the active PRP Cisco IOS is enabled and this PRP is in standby mode Checking the Installation Checking the Installation Verifying Interface Status ETH Bits Upgrading to the PRP Router# show redundancy Upgrading to the PRP Without Rebooting the Router Router# dir disk1 Prompted to abort the copy, type n SSO or RPR+ mode because the RPs are running the same imageIs correct, continue with Step Another disk or at another location Upgrading to the PRP Upgrading to the PRP Upgrading to the PRP Upgrading to the PRP Verify the disk contents using the dir disk1 command Upgrading to the PRP With Rebooting the Router Upgrading to the PRP Use the command upgrade rom-monitor slot rp-slot 0x10 Differentiating Between PRP-1 and PRP-2 Configuring Interfaces on the PRP Configuring an Ethernet InterfaceEthernet Interface Receptacles, Cables, and Pinouts RJ-45 receptacle Category 5 UTP cable with plug Crossover Cable Pinout for Connecting Two PRPs Ethernet Port Pin Signal Description Lists Ieee 802.3u physical characteristics for 100BASE-TX Parameter RJ-45Parameter Ethernet Interface Cable Connection Procedure Using the Ethernet Port on the PRP Configuring the Ethernet Interfaces Using Configuration Mode to Configure an Ethernet Interface Configuring the Console Interface Console and Auxiliary Port Connections Signal Input/Output Description Configuring the Auxiliary Interface Description of the Software Configuration Register Understanding the Software Configuration Register Additional Configuration and Maintenance Tasks Bit Number Hexadecimal Value Meaning/Function Defines the bits in the software configuration register Boot Field Settings Boot Field MeaningDescribed in Table Command Purpose Configuring the Software Configuration Register Action/Filename Bit Bits in the Software Configuration Register Address net host Data Transmission Rate bps9600 4800 1200 2400 About Flash Disks Using Flash Disks in the PRP Product Number Removing and Installing a Flash Disk in the PRP Installing and Removing a Flash Disk Working with Flash Disks Installing a Flash Disk Boots the named file from the Flash disk in slot Booting from a Flash Disk Removing the CF from the PRP-2 Board Removing and Installing a Compact Flash Disk Removing and Installing a Hard Disk Drive Installing the Hard Disk Drive Recovering a Lost Password Initialize the router by entering the i command as follows Step Upgrading PRP Memory Locations of PRP Components and Memory 512 MB MB Dimm U15 MEM-PRP-512= MB DIMMs U15 and U18 GB Dimm U15GB DIMMs U15 and U18 Cisco Product Number Dimm Modules Sdram Dimm Sockets Removing a Dimm Dimm Socket with Dual Release Levers Installing a Dimm Handling a Dimm Checking the Dimm Installation Regulatory, Compliance, and Safety Information Translated Safety Warnings and Agency Approvals Electromagnetic Compatibility Regulatory StatementsFCC Class a Compliance Europe EU Canada Regulatory, Compliance, and Safety Information Vcci Class a Notice for Japan Class a Notice for Korea Obtaining Documentation Cisco.comProduct Documentation DVD Documentation Feedback Cisco Product Security OverviewOrdering Documentation For emergencies only security-alert@cisco.com Reporting Security Problems in Cisco Products Product Alerts and Field Notices Obtaining Technical AssistanceCisco Technical Support & Documentation Website Submitting a Service Request Definitions of Service Request Severity Obtaining Additional Publications and Information Obtaining Additional Publications and Information OL-11656-01