Manuals / Cisco Systems / Power Tools / Router

Cisco Systems PRP-2=, PRP-1=, PRP-1/R= manual PRP Functions, Shows the front panel view of the PRP-2

Models: PRP-1/R= PRP-1= PRP-2/R= PRP-2=

1 92

Download 92 pages 52.96 Kb

Page 6

Product Overview

Figure 2 shows the front panel view of the PRP-2.

Figure 2

PRP-2, Front Panel View

-1 SLOT-0 SLOT

LINK

DATA

LINK

DATA

SIG

ACT

SIG

ACT

ETH 0

ETH 1

BITS 0

BITS 1

AUX

CONSOLE

ETH 2	RESET	101104
ETH 2	PERFORMANCE ROUTE PROCESSOR 2
	PERFORMANCE ROUTE PROCESSOR 2

The PRP-2 is available as Product Number PRP-2 or PRP-2=, which includes one PRP with 1 G of synchronous dynamic random-access memory (SDRAM) and one 64-MB advanced technology attachment (ATA) Flash disk. A redundant PRP (Product Number PRP-2/R) is also available.

PRP Functions

The PRP-1 for the Cisco 12000 Series Router includes the following primary functions:

•Loading Cisco IOS software on all installed line cards at power up

•Providing a console (terminal) port for router configuration

•Providing an auxiliary port for other external equipment (such as modems)

•Providing two IEEE 802.3, 10/100-megabits-per-second (Mbps) Ethernet ports for Telnet functionality

•Running routing protocols

•Building and distributing routing tables to line cards

•Providing general system maintenance functions

•Communicating with line cards either through the switch fabric or through the maintenance bus (MBus). The MBus connection allows the PRP to download a system bootstrap image, collect or load diagnostic information, and perform general, internal system maintenance operations. The switch fabric connection is the main data path for routing table distribution as well as for packets that are sent between line cards and the PRP.

Performance Route Processor Installation and Configuration Guide

6	OL-11656-01

Image 6

Cisco Systems PRP-2=, PRP-1=, PRP-1/R=, PRP-2/R= manual PRP Functions, Shows the front panel view of the PRP-2

Contents

Document Contents Important Information Router InformationSupported Platforms Cisco IOS Software Requirements PRP Redundancy Hardware Revision Requirements Output from a later software release would be as follows Product Overview Related Documentation PRP Functions Shows the front panel view of the PRP-2 PRP Components Cisco IOS Software Storage PRP Hardware Components PRP-1 Horizontal Orientation PRP-2 Horizontal Orientation Program boot image Type Size Quantity Description LocationMB fixed Secondary CPU cache memory functions Sdram Status LEDs Flash MemoryPRP LEDs Following LEDs are used on the PRP Cisco IOS System Error Messages publications Display LEDs Soft Reset Switch Flash Disk Slots Asynchronous Serial Ports Ethernet PortsHard Disk Drive Preparing for Installation Safety GuidelinesCompact Flash Disk Preventing Electrostatic Discharge Removing and Installing a PRP Required Tools and EquipmentWorking with Electrical Equipment Removing a PRP Illustrates the PRP installed in a chassis Ejector Levers Shows the ejector levers in detail Installing a PRP Removing and Installing a PRP Checking the Installation PRP Boot Process Starting the System and Observing Initial Conditions Cisco IOS is enabled and this PRP is in standby mode Rommon for this PRP is enabled and recognized by the systemCisco IOS is enabled and this PRP is the active PRP LED Display Description Checking the Installation Checking the Installation Verifying Interface Status Upgrading to the PRP ETH Bits Upgrading to the PRP Without Rebooting the Router Router# show redundancy Router# dir disk1 Another disk or at another location SSO or RPR+ mode because the RPs are running the same imageIs correct, continue with Step Prompted to abort the copy, type n Upgrading to the PRP Upgrading to the PRP Upgrading to the PRP Upgrading to the PRP Upgrading to the PRP With Rebooting the Router Verify the disk contents using the dir disk1 command Upgrading to the PRP Use the command upgrade rom-monitor slot rp-slot Differentiating Between PRP-1 and PRP-2 0x10 Configuring Interfaces on the PRP Configuring an Ethernet InterfaceEthernet Interface Receptacles, Cables, and Pinouts RJ-45 receptacle Category 5 UTP cable with plug Ethernet Port Pin Signal Description Crossover Cable Pinout for Connecting Two PRPs Lists Ieee 802.3u physical characteristics for 100BASE-TX Parameter RJ-45Parameter Ethernet Interface Cable Connection Procedure Configuring the Ethernet Interfaces Using the Ethernet Port on the PRP Using Configuration Mode to Configure an Ethernet Interface Configuring the Console Interface Console and Auxiliary Port Connections Configuring the Auxiliary Interface Signal Input/Output Description Understanding the Software Configuration Register Description of the Software Configuration Register Additional Configuration and Maintenance Tasks Defines the bits in the software configuration register Bit Number Hexadecimal Value Meaning/Function Boot Field Settings Boot Field MeaningDescribed in Table Configuring the Software Configuration Register Command Purpose Bits in the Software Configuration Register Action/Filename Bit Address net host Data Transmission Rate bps9600 4800 1200 2400 Using Flash Disks in the PRP About Flash Disks Removing and Installing a Flash Disk in the PRP Product Number Installing and Removing a Flash Disk Installing a Flash Disk Working with Flash Disks Booting from a Flash Disk Boots the named file from the Flash disk in slot Removing and Installing a Compact Flash Disk Removing the CF from the PRP-2 Board Removing and Installing a Hard Disk Drive Installing the Hard Disk Drive Recovering a Lost Password Initialize the router by entering the i command as follows Step Upgrading PRP Memory Locations of PRP Components and Memory 512 MB MB Dimm U15 MEM-PRP-512= MB DIMMs U15 and U18 GB Dimm U15GB DIMMs U15 and U18 Removing a Dimm Cisco Product Number Dimm Modules Sdram Dimm Sockets Dimm Socket with Dual Release Levers Installing a Dimm Handling a Dimm Regulatory, Compliance, and Safety Information Checking the Dimm Installation Translated Safety Warnings and Agency Approvals Electromagnetic Compatibility Regulatory StatementsFCC Class a Compliance Canada Europe EU Regulatory, Compliance, and Safety Information Vcci Class a Notice for Japan Class a Notice for Korea Obtaining Documentation Cisco.comProduct Documentation DVD Documentation Feedback Cisco Product Security OverviewOrdering Documentation Reporting Security Problems in Cisco Products For emergencies only security-alert@cisco.com Product Alerts and Field Notices Obtaining Technical AssistanceCisco Technical Support & Documentation Website Submitting a Service Request Definitions of Service Request Severity Obtaining Additional Publications and Information Obtaining Additional Publications and Information OL-11656-01