Installing and Removing a Flash Disk | Cisco Systems PRP-2/R=

Additional Configuration and Maintenance Tasks

Figure 15

Flash Disk Slot Cover Removal and Installation

CLEAN

CLASS 1 LASER		PRODUCT
LASERPRODUKT			1
PRODUIT		DER KLASSE
	LASER DE CLASSE		1

0 1 2 3

ETH 0 ETH 1 AUX

PRIMARY

PRIMARY

TX

RX

CONSOLE

R

E

S

E

T

C R IT M ICALAJOMINO R R

40C48/POS-SR-SC

PERFORMANCE ROUTE PROCESSOR 1 (PRP-1)

MBUS

FAIL

ENABLE

CONSOLIDATED SWITCH FABRIC

75286

Figure 16 Installing and Removing a Flash Disk

EJECT	SLOT	ETH 0			ETH 1		AUX	CONSOLE
EJECT	SLOT			RX			RX
	-1
	-0
	SLOT		EN	TX		EN	TX
			EN			EN
	PRIMARY		LINK		PRIMARY	LINK		RESET
	PRIMARY		LINK		PRIMARY	LINK		PERFORMANCE ROUTE PROCESSOR 1 (PRP-1)

75038

		Performance Route Processor Installation and Configuration Guide

	OL-11656-01			63
	OL-11656-01			63

Image 63

Cisco Systems PRP-2/R=, PRP-1=, PRP-1/R=, PRP-2= manual Installing and Removing a Flash Disk

Contents

Document Contents Important Information Router InformationSupported Platforms PRP Redundancy Cisco IOS Software Requirements Output from a later software release would be as follows Hardware Revision Requirements Related Documentation Product Overview Shows the front panel view of the PRP-2 PRP Functions PRP Components Cisco IOS Software Storage PRP Hardware Components PRP-1 Horizontal Orientation PRP-2 Horizontal Orientation Program boot image Type Size Quantity Description LocationMB fixed Secondary CPU cache memory functions Sdram Following LEDs are used on the PRP Flash MemoryPRP LEDs Status LEDs Display LEDs Cisco IOS System Error Messages publications Flash Disk Slots Soft Reset Switch Asynchronous Serial Ports Ethernet PortsHard Disk Drive Preparing for Installation Safety GuidelinesCompact Flash Disk Preventing Electrostatic Discharge Removing and Installing a PRP Required Tools and EquipmentWorking with Electrical Equipment Removing a PRP Ejector Levers Illustrates the PRP installed in a chassis Shows the ejector levers in detail Installing a PRP Removing and Installing a PRP PRP Boot Process Checking the Installation Starting the System and Observing Initial Conditions LED Display Description Rommon for this PRP is enabled and recognized by the systemCisco IOS is enabled and this PRP is the active PRP Cisco IOS is enabled and this PRP is in standby mode Checking the Installation Checking the Installation Verifying Interface Status ETH Bits Upgrading to the PRP Router# show redundancy Upgrading to the PRP Without Rebooting the Router Router# dir disk1 Prompted to abort the copy, type n SSO or RPR+ mode because the RPs are running the same imageIs correct, continue with Step Another disk or at another location Upgrading to the PRP Upgrading to the PRP Upgrading to the PRP Upgrading to the PRP Verify the disk contents using the dir disk1 command Upgrading to the PRP With Rebooting the Router Upgrading to the PRP Use the command upgrade rom-monitor slot rp-slot 0x10 Differentiating Between PRP-1 and PRP-2 Configuring Interfaces on the PRP Configuring an Ethernet InterfaceEthernet Interface Receptacles, Cables, and Pinouts RJ-45 receptacle Category 5 UTP cable with plug Crossover Cable Pinout for Connecting Two PRPs Ethernet Port Pin Signal Description Lists Ieee 802.3u physical characteristics for 100BASE-TX Parameter RJ-45Parameter Ethernet Interface Cable Connection Procedure Using the Ethernet Port on the PRP Configuring the Ethernet Interfaces Using Configuration Mode to Configure an Ethernet Interface Configuring the Console Interface Console and Auxiliary Port Connections Signal Input/Output Description Configuring the Auxiliary Interface Description of the Software Configuration Register Understanding the Software Configuration Register Additional Configuration and Maintenance Tasks Bit Number Hexadecimal Value Meaning/Function Defines the bits in the software configuration register Boot Field Settings Boot Field MeaningDescribed in Table Command Purpose Configuring the Software Configuration Register Action/Filename Bit Bits in the Software Configuration Register Address net host Data Transmission Rate bps9600 4800 1200 2400 About Flash Disks Using Flash Disks in the PRP Product Number Removing and Installing a Flash Disk in the PRP Installing and Removing a Flash Disk Working with Flash Disks Installing a Flash Disk Boots the named file from the Flash disk in slot Booting from a Flash Disk Removing the CF from the PRP-2 Board Removing and Installing a Compact Flash Disk Removing and Installing a Hard Disk Drive Installing the Hard Disk Drive Recovering a Lost Password Initialize the router by entering the i command as follows Step Upgrading PRP Memory Locations of PRP Components and Memory 512 MB MB Dimm U15 MEM-PRP-512= MB DIMMs U15 and U18 GB Dimm U15GB DIMMs U15 and U18 Cisco Product Number Dimm Modules Sdram Dimm Sockets Removing a Dimm Dimm Socket with Dual Release Levers Installing a Dimm Handling a Dimm Checking the Dimm Installation Regulatory, Compliance, and Safety Information Translated Safety Warnings and Agency Approvals Electromagnetic Compatibility Regulatory StatementsFCC Class a Compliance Europe EU Canada Regulatory, Compliance, and Safety Information Vcci Class a Notice for Japan Class a Notice for Korea Obtaining Documentation Cisco.comProduct Documentation DVD Documentation Feedback Cisco Product Security OverviewOrdering Documentation For emergencies only security-alert@cisco.com Reporting Security Problems in Cisco Products Product Alerts and Field Notices Obtaining Technical AssistanceCisco Technical Support & Documentation Website Submitting a Service Request Definitions of Service Request Severity Obtaining Additional Publications and Information Obtaining Additional Publications and Information OL-11656-01