Appendix K

Configuration of Multiple Subnets

Appendix K:

 

RVL200-to-RV042 Configuration

 

Configuration of Multiple

 

two static routes on the RVL200. Then on each RV042, you

Subnets

 

To create this configuration, you create two subnets and

 

static route.

 

 

 

 

 

 

 

 

 

 

set it to Router mode, disable the firewall, and set up a

Overview

 

RVL200 Configuration

The 4-Port SSL/IPSec VPN Router (model number: RVL200)

 

1. Physically connect a numbered port (Ethernet 1-4) on

 

the RVL200 to the WAN 1 port of the RV042.

can support multiple subnets. The configuration example

 

 

 

 

 

 

 

 

shows an RVL200 deploying two routers.

 

2. Access the web-based utility of the RVL200. (Refer to

Any router can be deployed; however, this example uses

 

“Chapter 4: Advanced Configuration” for details.)

 

3. Click the Setup tab.

the Linksys 10/100 4-Port VPN Router (model number:

 

RV042).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Static Route #1

RVL200

 

 

 

 

 

 

Destination IP: 192.168.7.0

 

 

 

 

 

 

Subnet Mask: 255.255.255.0

LAN IP: 192.168.1.1

 

 

 

 

 

 

 

 

 

 

 

 

Default Gateway: 192.168.1.2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Multiple Subnet

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Interface: LAN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Static Route #2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IP: 192.168.7.0/24

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Destination IP: 192.168.20.0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Multiple Subnet

 

 

 

 

 

 

Subnet Mask: 255.255.255.0

 

 

 

 

 

 

Default Gateway: 192.168.1.20

IP: 192.168.20.0/24

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Interface: LAN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RV042 #1

WAN IP: 192.168.1.2

LAN IP: 192.168.7.254

Working Mode: Router

Firewall: Disabled

 

Static Route

 

 

Destination IP: 192.168.20.0

 

 

Subnet Mask: 255.255.255.0

192.168.1.x

192.168.7.x

Default Gateway: 192.168.1.20

 

 

Interface: WAN1

 

RV042 #2

WAN IP: 192.168.1.20

LAN IP: 192.168.20.254

Working Mode: Router

Firewall: Disabled

 

 

Static Route

 

 

Destination IP: 192.168.7.0

 

 

Subnet Mask: 255.255.255.0

Default VLAN1

192.168.20.x

Default Gateway: 192.168.1.2

 

Interface: WAN1

 

 

RVL200 with Multiple Subnets

4-Port SSL/IPSec VPN Router

 

91

Page 99
Image 99
Cisco Systems manual Appendix K, Configuration of Multiple, Subnets, RVL200-to-RV042 Configuration