Manuals / Cisco Systems / Computer Equipment / Network Card

Cisco Systems SCE 2000 4xGBE manual Back Panel

Models: SCE 2000 4xGBE

1 152

Download 152 pages 7.79 Kb

Page 22

Back Panel

Chapter 2 Overview of the SCE 2000 Platform

Back Panel

Back Panel

The SCE 2000 platform back-panel contains the following components:

•Two field-replaceable power supply units with ON/OFF switches

•A field-replaceable fan drawer

•Ground connections

•Two connectors to the external bypass module

The rear panels of both the AC- and DC-powered SCE 2000 platforms are shown in the following pair of figures.

Figure 2-3: SCE 2000 Back Panel: AC Power

Figure 2-4: SCE 2000 Back Panel DC power

SCE 2000 4xGBE Installation and Configuration Guide

2-6	OL-7824-02

Image 22

Cisco Systems SCE 2000 4xGBE manual Back Panel

Contents

Corporate Headquarters SCE 2000 4xGBE Installation and Configuration GuideVersion OL-7824-02 Cisco Systems, Inc 170 West Tasman Drive San Jose, CA USASCE 2000 4xGBE Installation and Configuration Guide Turn the television or radio antenna until the interference stopsIntroduction C O N T E N T SPreface Overview of the SCE 2000 PlatformConnecting the Management Interfaces and Performing Initial System Installation and MaintenanceConfiguration Cabling the Line Ports and Completing the Installation Basic SCE 2000 Platform OperationsThe External Optical Bypass Module A-1 TroubleshootingIndex Preface AudienceMaintenance on page OrganizationInstallation and Connecting theRelated Publications Obtaining Documentation on pageitalic font Document Conventionsboldface font boldface screen fontCisco.com Obtaining DocumentationObtaining Technical Assistance Documentation FeedbackDefinitions of Service Request Severity Submitting a Service RequestObtaining Additional Publications and Information Preface Obtaining Additional Publications and Information SCE 2000 4xGBE Installation and Configuration GuideOL-7824-02 Page C H A P T E R IntroductionSCE Platform Management Interfaces Chapter SCE Platform Management InterfacesSCE Platform Management Interfaces Checking the Shipping Container Contents Service Control and the SCE PlatformService Control and the SCE Platform SCE 2000 Installation ChecklistSCE 2020 4xGBE Service Control ManagementModel number Link TypeChapter 2 Overview of the SCE 2000 Platform Front Panel Front PanelSCE 2000 4xGBE Installation and Configuration Guide Figure 2-2 SE2000 Front PanelDescription PortQuantity Connect This Port To…LED Groups DescriptionBack Panel Checking the Shipping Container Contents SCE 2000 Component ListSCE 2000 Installation Checklist Verified SCE 2000 Installation ChecklistTask DatePage Topology Considerations TopologyThe SCE 2000 Platform The SCE 2000 Platform Topology ConsiderationsNumber of links FunctionalityRedundancy Link Continuity Bypass MechanismSingle SCE 2000 Topologies Physical TopologiesSingle Link Receive-only Topology Figure 3-2 Single SCE Platform Single Link In-line Topology Dual link Inline InstallationSingle Link Inline Topology Figure 3-3 Single SCE Platform Dual Link Inline TopologyTwo Cascaded SCE 2000s For Dual Links Dual Link Receive-Only TopologyTopology-Related Parameters Two Cascaded SCE 2000s Inline TopologyConnection Mode Parameter SCE 2000 ConfigurationInline/Receive-only Physically Connected Links Parameter On-Failure Mode ParameterPriority Page Preparing to Install the SCE 2000 Platform Installation and MaintenancePreparing to Install the SCE 2000 Platform Installing the SCE 2000 PlatformTools and Parts Required Site Requirement Guidelines AirflowInstalling the SCE 2000 Platform Site RequirementsInstalling the SCE 2000 on a Workbench or Tabletop on page Installation PrecautionsInstallation Precautions on page Attaching a Chassis Ground Connection on pageInstalling the SCE 2000 on a Workbench or Tabletop Rack-Mounting a SCE 2000 Platform Mounting Brackets for 2-post Rack Mounting Brackets for 4-post RackAttaching the Brackets to the SCE Attaching the Crossrail Supports to the Rack Step 3 Repeat steps 1 and 2 on the other side of the SCEFigure 4-6 Assembling the Slider Brackets Mounting the System to the Rack SCE 2000 4xGBE Installation and Configuration Guide Chapter 4 Installation and MaintenanceInstalling the SCE 2000 Platform Figure 4-8 Sliding the SCE 2000 into the RackAttaching a Chassis Ground Connection Figure 4-9 Securing the SCE 2000 to the RackFigure 4-10 Grounding the Unit AC SCE 2000 4xGBE Installation and Configuration Guide Chapter 4 Installation and MaintenanceInstalling the SCE 2000 Platform Figure 4-11 Grounding the Unit DCPower Supply Overview LEDs Power Supply Unit Condiiton Power Supply SpecificationsPower Supply Unit Condition LED StateRemoving the Power Supply Unit on page Removing and Replacing a Power Supply UnitPowering Down the Power Supply Unit and Disconnecting Input Power Replacing the Power Supply Unit on pagePowering Down an AC-Input Power Supply Removing the Power Supply Unit Replacing the Power Supply UnitReconnecting AC-Input Power Supply Unit on page Reconnecting the PowerReconnecting AC-Input Power Supply Unit Reconnecting DC-Input Power Supply Unit on pageReconnecting DC-Input Power Supply Unit Step 6 Turn the on/off switch to the on position Removing and Replacing the Fan Module Fan Module OverviewRemoving the Fan Module on page Replacing the Fan Module on page Removing the Fan Module Replacing the Fan ModuleFigure 4-17 Inserting the Fan Module Replacing the Battery Connecting the Local Console Performing Initial System ConfigurationConnecting the Local Console Initial System ConfigurationSetting Up the Local Console Initial System Configuration admin password Following are some general instructions regarding the setup dialog Step 1 Configuring Initial Settings appear “Sorry, Skipping is not allowed at this stage.”Enter IP address of default gateway Step 2 Configuring the HostnameStep 3 Setting the Passwords Enter IP address Enter IP subnet mask255.255.0.0Note Passwords are case sensitive Step 4 Configuring Time SettingsNote The default password for all levels is “cisco” To configure the time settings, complete the following steps Step 5 Configuring the DNS Settings EnterStep 3 Type the default domain name to be used, and press Enter Step 6 Configuring the RDR Formatter Destination Step 7 ConfiguringAccess Control Lists ACLs Entry Formatsdeny 10.1.1.0 permit any Order of Entriespermit any deny EnterStep 7 The maximum number of entries in an ACL is We want to restrict Telnet access to only a few permitted stations Enable SNMP management? no y Step 8 Configuring SNMPWould you like to enter the SNMP configuration menu? no y Enter SNMP GET community nameStep 8 The maximum number of SET communities is To disable the Authentication Failure trap, press Enter Step 9 Configuring the Topology-Dependent Parameters Secondary To specify Primary, press Enter EXAMPLE #2 EXAMPLE #3Step 10 Completing and Saving the Configuration Step 6 The system informs you that the configuration is complete Cabling the Management Port on page Connecting the Management InterfaceVerifying Management Interface Connectivity on page Cabling the Management Port Verifying Management Interface Connectivity C\ping 10.1.1.201 pinging PING 10.1.1.201 56 data bytes Page Connecting the line ports to the network Cabling the Line Ports and Completing the InstallationConnecting the line ports to the network Installing a Cascaded SystemSingle Link Receive-only Topology on page Cabling DiagramsSingle Link Inline Topology on page Dual Link Single SCE 2000 Topologies on pageDual Link Single SCE 2000 Topologies Single Link Receive-only TopologyFigure 6-3 Cabling Diagram Dual Link One SCE 2000 Inline Figure 6-4 Cabling Diagram Dual Link One SCE 2000 Receive-onlySCE 2000 #1 Dual Link Two SCE 2000s TopologySCE 2000 #2 Inline topologies require connecting both Receive and Transmit fibers to the SCE 2000. Cascade ports always require both Receive and Transmit fibers to be connected Configuring GigabitEthernet Auto-Negotiation Configuring the GBE Interface ParametersStep 3 Type auto-negotiate and press Enter Fiber Specifications Connecting the GBE Line Interface PortsCabling the GBE Port Step 2 Verify that the link LED is green Figure 6-6 Cabling the GBE InterfaceViewing the Counters to Verify that the Network Traffic is Testing Connectivity Examining Link LEDs and CountersExamining the LEDs Reaching the DeviceThe following example displays a system response Installing a Cascaded System Configuring the Connection Mode CLI CommandsTopology-Related Parameters for Redundant Topologies Link Mode Monitoring the System links forwardingbypasssniffingcutoff and press EnterService Control Application Suite for Broadband User Guide Loading and Activating a Service Control ApplicationService Control Application Suite for Broadband Reference Guide Rebooting and Shutting Down the SCE Platform Managing SCE 2000 ConfigurationsPerforming Complex Configurations Basic SCE 2000 Platform OperationsStarting the System and Observing Initial Conditions Viewing the User Log Counters Final TestsVerifying Operational Status Verifying Operational Status on pageViewing Configuration on page Managing SCE 2000 ConfigurationsViewing Configuration Saving the Configuration Settings on pageTo view the running configuration, complete the following steps Step 1 At the SCE 2000# prompt, type show version Saving the Configuration Settings Step 3 Type copy running-config startup-configThe following example shows the running configuration file Recovering a Previous Configuration copy tffs0system/prevconf/config.tx1 tffs0system/config.txtCisco Service Control Engine SCE Software Configuration Guide Performing Complex ConfigurationsCisco Service Control Engine SCE CLI Command Reference Rebooting and Shutting Down the SCE Platform Rebooting the SCE PlatformShutting Down the SCE Platform Step 2 Type reload shutdownTroubleshooting Overview Problem Solving Using a Subsystems Approach TroubleshootingTroubleshooting Overview C H A P T E RCLI Commands for Troubleshooting on page The User Log on page Troubleshooting ToolsCLI Commands for Troubleshooting Troubleshooting firmware package installationTroubleshooting the management subsystem Troubleshooting the link interface subsystemThe User Log The Logging SystemViewing the User Log ftp//usernamepassword@ipaddress/path and press EnterCopying the User Log Step 1 From the SCE 2000# prompt, type logger get user-log file-nameThe system asks Are you sure? Clearing the User LogViewing the User Log Counters Type Y and press EnterFront Panel on page Check the LEDsGenerating a File for Technical Support SCE 2000 Operational Status on pageInitial state after reset SCE 2000 Operational StatusBooting Boot is completedIdentifying Startup Problems Problem Solving Using a Subsystems ApproachTroubleshooting the Power Subsystem Possible Cause SymptomPossible Solution LED Labelconfigure Boot system filename Troubleshooting the Firmware Package InstallationDiagnostic Action SymptomDiagnostic Action Troubleshooting the Management SubsystemSymptom Possible SolutionSoftware Configuration Guide See Initial System ConfigurationRefer to IP Configuration in See Initial System ConfigurationTroubleshooting the Link Interface Subsystem Check auto-negotiation Configuring the GBEConfiguring the GBE show interfacePage The External Optical Bypass Module A P P E N D I X AExternal Optical Bypass Functionality Figure A-1 External Optical Bypass Module Inactive not in bypassFigure A-2 External Optical Bypass Module Active in bypass The External Optical Bypass Module Front Panel Installing the External Bypass Module Installing the Module in a RackCabling the External Optical Bypass Module To cable the External Optical Bypass module Step 6 Connect the control cable supplied in the kit from the Bypass 9-pin D-Type connector on the rear panel of the SCE 2000 platform to the Control connector on the External Optical Bypass module Function SpecificationsValue Pin D-type sidePage Index Page