Extron electronic 68-1383-01 REV. E Signal Inputs, Mtpx Plus 3232 Twisted Pair Matrix Switcher

Figure 4 shows the rear panel of the MTPX Plus 3232.

4

5

							2		7
						LOCAL INPUTS
	INPUT			1			2		3
	SELECT
	LOCAL
				4			5		6
	RJ-45
		RS-232 OUTPUT INSERTION							LOCAL OUTPUTS
1	2	3	4	5	6	7		8
Tx Rx	Tx Rx	Tx Rx	Tx Rx	Tx Rx	Tx Rx	Tx Rx	Tx Rx
									1
9	10	11	12	13	14	15		16
Tx Rx	Tx Rx	Tx Rx	Tx Rx	Tx Rx	Tx Rx	Tx Rx	Tx Rx		2
3.2A MAX

AUDIO INPUTS

L 1 R L 2 R L 3 R L 4 R L 5 R

1

																	INPUTS
	1		2		3		4			5		6		7		8			9		10		11		12			13	14	15	16	LISTED
																																US 1T23
																																I.T.E.
																				INPUTS
	17		18		19		20			21		22		23		24			25		26		27		28			29	30	31	32
																	OUTPUTS
	1		2		3		4			5		6		7		8			9		10		11		12			13	14	15	16
	17		18		19		20			21		22		23		24			25		26		27		28			29	30	31	32
													MONO AUDIO OUTPUTS																	CONTROL
																													ETHERNET
L	6	R		L	1	R	L	2	R	L	3	R	L	4	R	L	5	R	L	6	R	L	7	R	L	8	R			RESET

6

ACT LINK

13 3 8 11 12 10

Figure 4. MTPX Plus 3232 Twisted Pair Matrix Switcher

NOTE: The MTPX Plus 1632 and MTPX Plus 3216 are housed in the same 3U enclosure,

but have fewer input connectors (16 x 32 matrix) or output connectors (32 x 16 matrix) to accommodate their smaller matrix sizes.

CAUTIONS: • Use Electrostatic discharge (ESD) precautions (that is, be electrically grounded) when making connections. Electrostatic discharge can damage equipment, even if you cannot feel, see, or hear it.

•Remove system power before making any connections.

Signal Inputs

aInputs (TP) connectors — Connect the TP outputs of compatible MTP or VTT transmitters to these RJ-45 female connectors.

CAUTION: Do not connect this device to a computer data or telecommunications network.

NOTES: • Configure the switcher for the appropriate content on the audio/RS-232 wire pair (pins 3 and 6) for each TP input (see “Defining the Audio/

RS-232 Wire Pair“ in the “Operation” section). You can also use

SIS commands (see the “Programming Guide” section), the Matrix

Switchers Control Program (see the “Matrix Software“ section), or the

HTML pages (see the “HTML Operation” section).

• For best results, use a minimum cable length of at least 25 feet (7.5 m) between the transmitter and the MTPX input and between the MTPX output and the transmitter.

• RJ-45 termination with CAT 5, CAT 5e, or CAT 6 cable must comply with the TIA/EIA T568A or TIA/EIA T568B wiring standards for all connections.

RJ-45 termination with Enhanced Skew-Free A/V UTP cable must comply with TIA/EIA T568A only.

• For low resolution MTPs (S-video and composite video) on the TP inputs, the MTPX Plus audio circuits are compatible only with the newer generation, mono audio models. See your MTP transmitter/ receiver and refer to the associated manual to determine which MTP models you have.

MTPX Plus Series • Installation 12