Html Operation | Extron electronic 3200, 7200 instruction

HTML Operation

This section introduces using the built-in HTML pages to operate the FOX Matrix Switchers, including:

•Opening the Embedded Web Pages

•Status Tab

•Configuration Tab

•File Management Tab

•Control Tab

The switcher can be controlled and operated through its LAN port, connected via a LAN or WAN, using a web browser such as the Microsoft Internet Explorer. The display in the browser of the status or operation of the switcher has the appearance of web pages. This chapter describes the factory-installed HTML pages, which are always available and cannot be erased or overwritten.

NOTE: If your Ethernet connection to the matrix switcher is unstable, try turning off the proxy server in your web browser. In Microsoft Internet Explorer, click Tools > Internet Options > Connections > LAN Settings, uncheck the Use a proxy server... box, and then click OK.

FOX Matrix 3200 and 7200 Switchers • HTML Operation 93

Image 101

Extron electronic 3200, 7200 manual Html Operation

Contents

User Guide Safety Instructions English Safety Instructions Trademarks Copyright Produit laser de classe FDA/IEC 60825-1 Requirements Software Commands Specifications AvailabilityConventions Used in this Guide NotificationsPage Contents 117 109Matrix Software Html Operation About this Guide About the FOX Matrix Switchers Typical FOX Matrix 3200 Application FOX Matrix 7200 8U high FOX Matrix 3200 4U high Tie any input to any or all outputs FeaturesFiber Cable Transmission Modes Redundant Power Supply Backs up Primary FOX Matrix 3200 and 7200 Switchers Introduction Configure the Matrix Switcher Setup and Installation ChecklistPerform Physical Installation Get Ready FOX Matrix 3200 Fiber Optic Matrix Switcher Rear Panel Rear Panel Boards, Cabling, and Features Primary Power Supply Slot Boards Connections Fiber optic boards 3G/HD/SD-SDI boards Fiber optic I/O board LED indicationsOutput LED Input LED Definition Indication Definition Cabling Remote PortEthernet Connection RJ-45 connector wiring Reset Button and LED Simple FOX Matrix Switcher External Sync Connection Example Switch Reference Connections Cooling Fan assemblies Power Supply Modules and Indicator LEDs Optional 9-pin TRS RS-232 Cable Front Panel Configuration Port Operation Front Panel Controls and Indicators Front Panel, FOX Matrix 7200 Switcher Through Input and Output Buttons FOX Matrix 3200 and 7200 Switchers Operation Lock Control Buttons Primary and Redundant Power Supply LEDs Power Indicators Button Icons Rear Panel Power Indicators Definitions Front Panel Operations Creating a Configuration Power Example 1 Create a set of ties 3 4 5 6 7 8 15 17 18 19 20 21 22 23 24 31 Example 2 Add a tie to a set of ties Final Configuration, Example Example 3 Remove a tie from a set of ties Select the output Press and release the output 4 button Example 4 Viewing ties Viewing the Configuration 4 5 6 7 8 15 18 19 20 21 22 23 24 31 O Grouping of Incompatible Video Formats Grouping Press the View button to select group Press the Preset button to select groupPress the Enter button to select group Assign inputs and outputs to group Example 5 Grouping inputs and outputs Select group 2 Press and release the Preset button Example 6 Saving a preset Using Presets Example 7 Recalling a preset Example 8 Muting and unmuting an output Muting and Unmuting Outputs Mute outputs one at a time Performing a System Reset from the Front Panel Locking the Front Panel Executive Mode Selecting the Rear Panel Remote Port Protocol and Baud Rate Background Illumination Reset Operations See the Matrix Software Soft System Resets Performing Soft System Resets Resets 3, 4, Performing a Hard Reset Reset Troubleshooting Worksheet Example 1 System equipment Configuration Worksheets Worksheet Example 2 Daily Configuration Worksheet Example 2 Daily Configuration Worksheet Example 3 Test Configuration Worksheet Example 3 Test configuration Blank Configuration worksheet, FOX Matrix Output destinations Programming Guide Serial Ports Ethernet LAN Port Default IP addressesEstablishing a Connection IP address Subnet mask 255.255.0.0 Gateway address Connection Timeouts Host-to-Switcher InstructionsUsing Verbose Mode Number of Connections Switcher-initiated Messages Using the Command and Response Tables Switcher Error Responses Symbol Definitions Command and Response Table for SIS Commands Channel mute commands Command and Response Table for SIS CommandsCreate ties Read ties Direct write process Save, recall, and directly write global presetsReclocking Laser controls EVM View ties, mutes, and presets Example 32 x 32 matrix LS List input link detection Names Grouping File management Front panel lockout Executive modeResets Information requests Example Matrix X5 = X6$ = Community names Port mappingUnit contact name and location Special Characters Access enableTrap targets Trap target notifications Software Operation via Ethernet Matrix Switchers Control ProgramEthernet protocol settings Software Operation via a Serial Port Installing the Software Comm Port Selection Window Using the Matrix Switcher Control Software If the IP address is correct Proceed to b Address and Password Entry Sample Program Window Icons Assigned and Ties Created Address and Name fields IP Settings/Options window Date, Time local, and GMT offset fields Hardware Address fieldUse Dhcp check box Use Daylight Saving check box Administrator Password and User Password fieldsSync Time to PC button Mail Addressee fields Mail Server IP Address fieldMail Server Domain Name field Updating the Firmware Downloading Firmware Upgrade Files Ethernet-connected firmware upload Extron Firmware Loader Window Serial-port-connected firmware upload Html Files List Window Uploading Html Files File menu Windows Buttons, Drop Boxes, and Trash CanWindows menus Status Window Tools menu Physical Configuration Window Ties Shown as Lines Preferences menu Master-Reset selection Using Emulation Mode Emulate Mode Configuration Using the Help System Button Label Generator Program Installing the Button Label Generator Software Extron Button Label Generator Window Using the Button Label Generator Software Html Operation Windows Security Dialog Box Opening the Embedded Web Pages System Status Status Tab Input Link Input Link System Settings Configuration TabIP Settings fields Unit Name field IP Address field Dhcp radio buttonsGateway IP Address field Subnet Mask field Date/Time Settings Fields Date/Time Settings fields Resetting a password Passwords Domain Name field Email SettingsMail IP Address field Email Address fields Setting up Smtp authorizationDeselecting Smtp authorization Snmp Settings Snmp Settings Snmp Manager Trap Target fields Snmp General Settings fields Firmware Upgrade Firmware Upgrade File Management File Management Tab Set and View Ties Control Tab Creating or deleting a tie FOX Matrix 3200 4U high FOX Matrix 7200 8U high Mounting the SwitcherUL Guidelines Mounting Instructions Battery and Power PrecautionsRemoving and Installing the I/O Board or Blank Panel FOX Matrix 7200 only Removing the I/O Board or Blank Panel Installing the I/O board or blank panel Installing the Power Supply Module Removing and Installing the Power Supply ModuleRemoving the Power Supply Module Removing a Fan Module Removing and Installing a Fan ModuleInstalling a Fan Module Installing Labels in the Buttons Removing and Installing Button Labels Button Label Blanks Ethernet Link Default IP Address Pinging to Determine the Web IP Address Pinging to Determine the Extron IP Address Configuring the Switcher for Network Use via the ARP Command Open Connecting as a Telnet ClientTelnet Tips Local echo Escape character and Esc keySet carriage return-line feed Close Gateways Subnetting a PrimerLocal and Remote Devices IP Addresses and Octets Masked octets are not compared indicated by X in figure Determining Whether Devices Are on the Same SubnetUnmasked octets are compared indicated by ? in figure Extron Warranty