Command and Response Table for IPSIS- CommandsSNMP-Specific(cont nued)SIS Commands (continued)

Command Function

SIS Command

Response

Additional description

 

(Host to Unit)

(Unit to Host)

 

IP setup commands (continued)

Set e-mail events for recipient

Example:

EX5#X5!,X5$,X5%,0EM} IpeX5#X5!*X5$*X5%*0]

EI69,63,3,0EM} IpeI69*63*3*0]

You must first have set an e-mail recipient for the X5! variable, using the separate Set e-mail recipient (CR) command on the previous page.

E-mail account #69 (recipient #5, JSmith), will receive fail/missing and fixed/restored messages for input 63.

Read e-mail notifications for one account (recipient)

Set DHCP on or off

Read DHCP on or off status Set serial port parameters

Read serial port parameters Set serial port mode Read serial port mode Set verbose mode

Read verbose mode Configure current port timeout Read current port timeout Configure global IP port timeout Read global IP port timeout

EX5#X5!,X5$,0EM

X5%X5%X5% ... X5%]

 

EX5^DH}

IdhX5^]

X5^: 0 = off, 1 = on

EDH}

X5^]

 

EX5&*X5*,X5(,X6),X6!CP}

 

 

 

CpnX5&•CcpX5*,X5(,X6),X6!]

EX5&CP}

X5*,X5(,X6),X6!]

 

EX5&*X6@CY}

CpnX5&•CtyX6@]

X6@: 0 = RS-232, 1 = RS-422

EX5&CY}

X6@]

 

EX6#CV}

VrbX6#]

 

ECV}

X6#]

 

E0*X6$TC}

Pti0*X6$]

 

E0TC}

X6*]

 

E1*X6$TC}

Pti1*X6$]

 

E1TC}

X6*]

 

SNMP setup commands

NOTE: See SNMP Settings Page, on page 103. This HTML page provides introductory information about Simple Network Management Protocol (SNMP) and is the preferred method for performing the functions listed below.

Port mapping

Map SNMP port

EAX6%PMAP}

PmapAX6%]

Reset SNMP port to default

EA161PMAP}

PmapA00161]

Disable SNMP port

EA0PMAP}

PmapA00000]

View current SNMP port

EAPMAP}

X6%]

Assign a specific port. Default:161.

Assign no port for SNMP. Assign a valid port to enable.

Unit contact name and location

NOTE: No contact or location (as opposed to NotSpecified, the default value) is not a valid entry.

Set unit contact info

Reset unit contact info to default View unit contact info

Set unit location info

Reset unit location info to default View unit location info

ECX6^SNMP}

SnmpC*X6^]

Set contact info to X6^.

ECSNMP}

SnmpC*NotSpecified]

 

ECSNMP}

X6^]

 

ELX6^SNMP}

SnmpL*X6^]

Set location info to X6^.

ELSNMP}

SnmpL*NotSpecified]

 

ELSNMP}

X6^]

 

Community names

Set unit read-only community name Reset read-only community name to default

View unit read-only name

Set unit read-write community name

Reset read-write community name to default

View unit read-write name

EPX6&SNMP}

SnmpP*X6&]

Set read-only (public) name to X6&.

EPSNMP}

SnmpP*public]

 

EPSNMP}

X6&]

 

EXX6&SNMP}

SnmpX*X6&]

Set read-write (private) name to X6&.

EXSNMP}

SnmpX*private]

 

EXSNMP}

X6&]

 

FOX Matrix 3200 and 7200 Switchers • Programming Guide 69

Page 77
Image 77
Extron electronic 3200, 7200 manual Port mapping, Unit contact name and location, Community names