Programming Guide | Extron electronic 7200, 3200 manual

Programming

Guide

This section describes the operation of the FOX Matrix Switchers via SIS commands, including:

•Serial Ports

•Ethernet (LAN) Port

•Host-to-Switcher Instructions

•Switcher-Initiated Messages

•Switcher Error Responses

•Using the Command and Response Tables

•Command and Response Table for SIS Commands

•Command Response Table for IP- and SNMP-Specific SIS Commands

•Special Characters

FOX Matrix 3200 and 7200 Switchers • Programming Guide 52

Image 60

Extron electronic 7200, 3200 manual Programming Guide

Contents

User Guide Safety Instructions Safety Instructions English Copyright Trademarks FDA/IEC 60825-1 Requirements Produit laser de classe Specifications Availability Software CommandsConventions Used in this Guide NotificationsPage Contents 109 117Matrix Software Html Operation About the FOX Matrix Switchers About this Guide Typical FOX Matrix 3200 Application FOX Matrix 7200 8U high FOX Matrix 3200 4U high Features Fiber Cable Transmission ModesTie any input to any or all outputs Redundant Power Supply Backs up Primary FOX Matrix 3200 and 7200 Switchers Introduction Setup and Installation Checklist Configure the Matrix SwitcherPerform Physical Installation Get Ready Rear Panel Boards, Cabling, and Features FOX Matrix 3200 Fiber Optic Matrix Switcher Rear Panel Primary Power Supply Boards Slot Fiber optic boards Connections Fiber optic I/O board LED indications 3G/HD/SD-SDI boardsOutput LED Input LED Definition Indication Definition Remote Port Ethernet ConnectionCabling Reset Button and LED RJ-45 connector wiring Switch Reference Connections Simple FOX Matrix Switcher External Sync Connection Example Power Supply Modules and Indicator LEDs Cooling Fan assemblies Front Panel Configuration Port Optional 9-pin TRS RS-232 Cable Front Panel Controls and Indicators Operation Front Panel, FOX Matrix 7200 Switcher Input and Output Buttons Through FOX Matrix 3200 and 7200 Switchers Operation Control Buttons Lock Power Indicators Primary and Redundant Power Supply LEDs Rear Panel Power Indicators Button Icons Front Panel Operations Definitions Power Creating a Configuration 3 4 5 6 7 8 15 17 18 19 20 21 22 23 24 31 Example 1 Create a set of ties Final Configuration, Example Example 2 Add a tie to a set of ties Example 3 Remove a tie from a set of ties Select the output Press and release the output 4 button Viewing the Configuration Example 4 Viewing ties 4 5 6 7 8 15 18 19 20 21 22 23 24 31 Grouping O Grouping of Incompatible Video Formats Press the Preset button to select group Press the Enter button to select groupPress the View button to select group Example 5 Grouping inputs and outputs Assign inputs and outputs to group Select group 2 Press and release the Preset button Using Presets Example 6 Saving a preset Example 7 Recalling a preset Muting and Unmuting Outputs Example 8 Muting and unmuting an output Mute outputs one at a time Locking the Front Panel Executive Mode Performing a System Reset from the Front Panel Background Illumination Selecting the Rear Panel Remote Port Protocol and Baud Rate Reset Operations See the Matrix Software Performing Soft System Resets Resets 3, 4, Soft System Resets Troubleshooting Performing a Hard Reset Reset Configuration Worksheets Worksheet Example 1 System equipment Worksheet Example 2 Daily Configuration Worksheet Example 2 Daily Configuration Worksheet Example 3 Test configuration Worksheet Example 3 Test Configuration Blank Configuration worksheet, FOX Matrix Output destinations Programming Guide Serial Ports Default IP addresses Ethernet LAN PortEstablishing a Connection IP address Subnet mask 255.255.0.0 Gateway address Host-to-Switcher Instructions Connection TimeoutsUsing Verbose Mode Number of Connections Switcher-initiated Messages Switcher Error Responses Using the Command and Response Tables Command and Response Table for SIS Commands Symbol Definitions Command and Response Table for SIS Commands Channel mute commandsCreate ties Read ties Save, recall, and directly write global presets Direct write processReclocking Laser controls View ties, mutes, and presets EVM List input link detection Example 32 x 32 matrix LS Grouping Names Front panel lockout Executive mode ResetsFile management Information requests Example Matrix X5 = X6$ = Port mapping Unit contact name and locationCommunity names Access enable Special CharactersTrap targets Trap target notifications Matrix Switchers Control Program Ethernet protocol settingsSoftware Operation via Ethernet Installing the Software Software Operation via a Serial Port Using the Matrix Switcher Control Software Comm Port Selection Window Address and Password Entry If the IP address is correct Proceed to b Sample Program Window Icons Assigned and Ties Created IP Settings/Options window Address and Name fields Hardware Address field Use Dhcp check boxDate, Time local, and GMT offset fields Administrator Password and User Password fields Sync Time to PC buttonUse Daylight Saving check box Mail Server IP Address field Mail Server Domain Name fieldMail Addressee fields Updating the Firmware Downloading Firmware Upgrade Files Ethernet-connected firmware upload Serial-port-connected firmware upload Extron Firmware Loader Window Uploading Html Files Html Files List Window Windows Buttons, Drop Boxes, and Trash Can Windows menusFile menu Tools menu Status Window Physical Configuration Window Preferences menu Ties Shown as Lines Using Emulation Mode Master-Reset selection Using the Help System Emulate Mode Configuration Installing the Button Label Generator Software Button Label Generator Program Using the Button Label Generator Software Extron Button Label Generator Window Html Operation Opening the Embedded Web Pages Windows Security Dialog Box Status Tab System Status Input Link Input Link Configuration Tab System SettingsIP Settings fields Unit Name field Dhcp radio buttons IP Address fieldGateway IP Address field Subnet Mask field Date/Time Settings fields Date/Time Settings Fields Passwords Resetting a password Email Settings Mail IP Address fieldDomain Name field Setting up Smtp authorization Deselecting Smtp authorizationEmail Address fields Snmp Settings Snmp Settings Snmp General Settings fields Snmp Manager Trap Target fields Firmware Upgrade Firmware Upgrade File Management Tab File Management Control Tab Set and View Ties Creating or deleting a tie Mounting the Switcher UL GuidelinesFOX Matrix 3200 4U high FOX Matrix 7200 8U high Battery and Power Precautions Removing and Installing the I/O Board or Blank PanelMounting Instructions FOX Matrix 7200 only Installing the I/O board or blank panel Removing the I/O Board or Blank Panel Removing and Installing the Power Supply Module Removing the Power Supply ModuleInstalling the Power Supply Module Removing and Installing a Fan Module Installing a Fan ModuleRemoving a Fan Module Removing and Installing Button Labels Installing Labels in the Buttons Button Label Blanks Default IP Address Ethernet Link Pinging to Determine the Extron IP Address Pinging to Determine the Web IP Address Configuring the Switcher for Network Use via the ARP Command Connecting as a Telnet Client Telnet TipsOpen Escape character and Esc key Local echoSet carriage return-line feed Close Subnetting a Primer GatewaysLocal and Remote Devices IP Addresses and Octets Determining Whether Devices Are on the Same Subnet Unmasked octets are compared indicated by ? in figureMasked octets are not compared indicated by X in figure Extron Warranty