Command and Response Table for SIS Commands (continued)
Command Function SIS Command | Response | Additional description |
(Host to Unit) | (Unit to Host) |
|
|
|
|
Reclocking |
|
|
NOTES:
•Laser board reclockers are set on a per SFP basis. If an SFP is reclocked, the corresponding input and output reclockers reclock at the same rate.
•
Set output reclocker | X$*X%= | RteX$*X%] |
Example: | 8*00= | Rte08*00] |
Read reclocker status | X$= | X%] |
Set the rate for reclocker X$ to X%. Set the rate for reclocker 8 to auto. Show current rate status for reclocker X$.
Laser controls
Enable individual laser driver
Disable individual laser driver Set individual output laser driver to automatic
Read status of all laser drivers
Global laser enable
EX!*1FIBR}
EX!*0FIBR} EX!*2FIBR}
EFIBR}
E1*FIBR}
FibrX!*1]
FibrX!*0]
FibrX!*2]
X^1X^2X^3X^4 ... X^n]
Fibr1]
Enable the laser for output X!. The laser lights so long as power is applied.
Disable the laser for output X!. The laser is off. Set the laser driver for output X! to automatic. The laser lights when a tie is made to output X!, but is off when no tie is made to output X! or the output is muted.
List the laser driver status of all installed outputs. n is the highest numbered output for your switcher. Enable all output laser drivers.
NOTE: If your switcher has any BNC
Global laser disable | E0*FIBR} | Fibr0] | Disable all output laser drivers. |
Global laser automatic | E2*FIBR} | Fibr2] | Set all output laser drivers to automatic. |
Save, recall, and directly write global presets
NOTES:
•If you try to recall a preset that is not saved, the matrix switcher responds with the error code E11.
•The following characters are invalid or not recommended in preset names: +
Save current configuration | X&, | SprX&] |
as a global preset |
|
|
Example: | 8, | Spr08] |
Recall a global preset | X&. | RprX&] |
Example: | 5. | Rpr05] |
Command character is a comma.
Save current ties as preset 8. Command character is a period.
Recall preset 5 (becomes the current configuration).
Direct write process —
NOTE: The direct write of a global preset should always be preceded by a clear global preset ties command of that same preset number. In a
If you do not clear the ties in a global preset number before you directly write a global preset to that number, ties that are part of the previous version of the specified preset with the same number can unexpectedly become part of the
Clear global preset ties | E+X&P0*!} |
|
|
|
| SprX&] | ||||
Directly write a global preset | E+X&PX!*X@!X!*X@%X!*X@! ... X!*X@&} | |||||||||
|
|
|
|
|
|
|
|
| SprX&] | |
Example: | E+27P0*!} |
|
|
|
| Spr27] | ||||
|
|
|
|
|
|
|
|
| ||
| Esc | +27P12*5!10*09%3*2!3*8& | ||||||||
|
|
|
|
|
|
|
|
| Spr27] | |
Clear all ties in preset X&.
Enter as many ties as are valid for this configuration. The ! tie, & tie, and % tie commands are all valid.
Clear all ties in preset 27.
Brackets are shown to separate ties for clarity only. Create global preset 27, which ties input 12 to output 5, input 10 to output 9, input 3 to output 2, and input 3 to output 8.
NOTE: X! = Input number (for tie) | 00 | – (maximum number of inputs for your configuration) (00 = untied) | ||
X@ = Output number | 01 | – (maximum number of outputs for your configuration) | ||
X$ = SFP or reclockable output | 00 – 32 or 72 (00 = global [SFP only]) |
| ||
X% = Output reclocking rate | 00 | = Bypass mode |
| 03 = 2.125 Gbps (laser boards only) |
| 01 | = Automatic mode (HDSDI boards only) | ||
X^ = Laser control | 02 | = 1.250 Gbps (laser boards only) | 04 = 4.250 Gbps (laser boards only) | |
0 = disable | 1 = enable (default) | 2 = automatic | ||
X& = Global preset number | 00 | – 32 (FOX Matrix 3200) or 64 (FOX Matrix 7200) (00 = current configuration) | ||
|
|
|
|
|
FOX Matrix 3200 and 7200 Switchers • Programming Guide 60
