Manuals / Faber / Photography / Security Camera

Faber M1600, M640, M1024, M1400 user manual Glossary of Terms

Models: M1600 M1400 M640 M1024

1 127

Download 127 pages 55.97 Kb

Page 121

Glossary of Terms

ARP

Address Resolution Protocol provides a way to retrieve the MAC address associated to an IP address.

Bandwidth

Describes the measure of data transfer capacity.

CAT5e Ethernet cable

Category 5e was designed for transmission speeds of up to 1 gigabit per second (Gigabit Ethernet).

CAT6 Ethernet cable

Same as Category 5e, except that it is made to a higher standard. Supports transmission speeds greater than Gigabit Ethernet with less signal attenuation over a given length of cable.

CCD – Charge-Coupled Device

A type of image sensor converting light into electrical charges.

Contiguous Memory

A block of physical memory occupying consecutive addresses.

DHCP (Dynamic Host Configuration Protocol)

Protocol which provides a mechanism for allocating IP addresses dynamically by a DHCP server on a network. Typically dedicated DHCP servers are a component of corporate networks. Used for managed networks.

Driver

Also called a device driver, a program routine that links a peripheral device to the operating system. a device driver is required for its frame grabber capabilities.

DSNU

Dark Signal Non-Uniformity (equivalent to FPN).

Ethernet Switch

A network device performing bridging at full wire-speed based on MAC addresses. Packet collisions are eliminated when using a full duplex switch. An Ethernet Switch operates at Layer 2 of the seven-layer OSI model.

FPN

Fixed Pattern Noise (equivalent to DSNU). FPN is the peak to peak difference between the minimum and maximum measured values for all active valid pixels sensor in darkness. Fixed Pattern Noise does not include a Random Noise component.

Frame

One complete image data set or its equivalent storage space.

Frame buffer

An area of memory used to hold a frame of image data. A frame buffer may exist on the acquisition hardware or be allocated by the acquisition hardware device driver in host system memory.

GigE Vision specification

Specification of the Automated Imaging Association (AIA, www.machinevisiononline.org). Defines the communication interface protocol used by any GigE Vision device.

Genie Monochrome Series-GigE Vision Camera

Glossary of Terms • 119

Image 121

Faber M1600, M640, M1024, M1400 user manual Glossary of Terms

Contents

Genie Framework M640 M1024 M1400 M1600 Genie Monochrome SeriesCA-GENM-MUM00 Contents Ynchronization T Iming Sapera Camexpert Guide Dalsa Contact Information Description Genie Monochrome Series OverviewGenie Application Advantages Genie Cables & Accessories sold separately Product number Camera Sensor Size ResolutionProduct Part Numbers Fps Product NumberCamera Performance Specifications Genie Sensor Overview Supported Industry StandardsCertifications RoHSItem / Feature Specification Genie M640-1/2 SpecificationsGenie M640-1/3 Specifications Genie M1024 Specifications ICX267AL Genie M1400 SpecificationsGenie M1600 Specifications Sapera LT Library with optional Processing Application Development OverviewGenICam Environment Page Supported Network Configurations Installing the Genie CameraUsing Genie with Ethernet Switches GigE Network Adapter GuidelineUsing Genie with a Vlan Ethernet Switch Installation Overview & PreparationsNetwork and Computer Overview Installation Overview Sapera LT Library InstallationProcedure Genie CD Package InstallationGigE Server Verification Connect the Genie Camera ConnectorsLED State Definition Status LED CodesTypical LED States on Power Up Genie IP Configuration SequenceGigE Server Status Increasing Adapter Buffers and Jumbo Frames Optimizing the Network Adapter used with GenieReceive Descriptors Select NIC Advanced Configuration PropertiesJumbo Frames Running the Network Configuration ToolUpdating Genie Firmware Page Quick Test with CamExpert About the User-Defined Camera Name Operational Reference Access Via CamExpertCamera and Sensor Information Read Only Parameters Power-up ConfigurationUser Set Parameters Parameter DescriptionCamera Information via Sapera LT or GenICam Applications SaperaSensor Parameters Controls Via CamExpert Sensor ControlsControls on Gain and Black Level Controls Partial Scan vertical cropping Partial Scan-Window ROIVertical Lines M640 M1024 M1400 Acquired Window ROI Partial Scan horizontal croppingWindow ROI Control via Sapera LT or GenICam Applications CamExpert Image Buffer and ROI Parameters Binning Binning Control via Sapera LT or GenICam Applications Trigger ModesFree-running Programmable Exposure Exposure ControlsExternal Trigger Programmable Exposure Exposure Controls via Sapera LT or GenICam Applications External Trigger Level-controlled ExposureSynchronization Timing Synchronous ModeSynchronization Mode via Sapera LT or GenICam Applications Reset ModeParameter Description CamExpert I/O Controls DialogGeneral Inputs Settings Via CamExpert External Input Signal Opto-coupler & Debounce CircuitGeneral Inputs TriggerSelector = not used Input Controls via Sapera LT or GenICam ApplicationsStrobe and General Outputs General Outputs Settings via CamExpertStrobe On Start of Exposure Event Mode Open and Close Output SettingsPulse On Invalid Trigger Event Mode Pulse On Valid Trigger Event ModePulse On End of Readout Event Mode Pulse On Start of Readout Event ModePulse On Input 1 or Input 2 Event Modes Pulse On End of Acquisition Event ModeOutput Control via Sapera LT or GenICam Applications Genie Processing FeaturesLookup Table LUT Sapera++ classes used LUT Control via Sapera LT or GenICam ApplicationsFlat Field Image Shading Correction Flat Field Correction Calibration ProcedureCamExpert Flat Field Calibration Menu Using Flat Field Correction Horizontal Image FlipVertical Genie test patterns are Internal Image Test PatternsTest Image Select via Sapera LT or GenICam Applications EventsSapera Callbacks Transfer Event Name Description Event Selection via GenICam ApplicationsCamExpert GigE Vision Parameters Network Controls & GigE Vision ParametersNetwork Controls via Sapera LT or GenICam Applications ROI Genie Power-up ConfigurationPower-up Control via Sapera LT or GenICam Applications Sapera Supported Features ListAccessing Features with Sapera++ LT Feature Type Enum Feature Type StringFeature Name Access Type Value Feature Name Access Type ValuesLUTFormat Feature Name Access Type Exponent Sample Value Feature Type INT32Feature Interdependence Diagrams Feature Type BoolTrigger Enable False Trigger Enable TrueVertical Binning Output SelectorHorizontal Binning Pixel Format Network Configuration ModePage Network Tools IP Configuration Mode DetailsLink-Local Address LLA Persistent IP Dhcp Dynamic Host Configuration ProtocolQuick Genie Network Configuration Network Configuration ToolSystem Information and Configuration NIC IP and Network Imaging Driver Assignment Network Card Information and ConfigurationTo recover a Genie Recovering a Camera with an Unknown Persistent IPSapera GigE Server Details Status Window Description Creating a Status ReportSapera CamExpert Guide Using CamExpert with Genie Monochrome CamerasCamExpert Panes Software trigger button CamExpert LUT ControlsBit Invert LUT Mechanical Specifications Technical SpecificationsPin Hirose Connector Signal Details ConnectorsPin Direction Genie Signal see details below External Inputs Genie Signal Electrical DetailsInput Electrical Parameter Description Value External Outputs RJ45 LAN Ethernet Connector DetailsOutput Electrical Parameter Description Value Network Connection Network ActivityOptical Considerations Camera Status LEDIllumination Light SourcesFilters Magnification and ResolutionLens Modeling Primary Points in a Lens SystemElectrostatic Discharge and the CCD Sensor Sensor Handling InstructionsProtecting Against Dust, Oil and Scratches Environment Cleaning the Sensor WindowRuggedized RJ45 Ethernet Cables Computer Requirements for Genie Cameras Ethernet Switch RequirementsHost PC System Ethernet to Fiber-Optic Interface Requirements EC & FCC Declaration of Conformity Problem Type Summary TroubleshootingOverview Device Available but with Operational Issues Device IP ErrorDevice Not Available GigE Server Warning Example 1a IP error with multiple NICs Installation Issues and Functional ProblemsGigE Server Warning Example 1b IP error with multiple NICs GigE Server Warning Example 3 Filter Driver CorSnid Disabled GigE Server Warning Example 2 Subnet Mask or IP errorFirmware Updates Device Available with Operational IssuesStreaming Error No Acquisition with a Timeout Message Power Failure During a Firmware Update-Now What?Disabling Windows Firewall Turning Windows Firewall Off Cabling and IP Configuration Issues Test a Genie Using Internal Test PatternsStreaming Video grab Issues Grab has Random Bad Data or Noise Grab Remains BlackGrab has Random Bad Data or Noise Case Laptop Computer Networking Issues Problems when Changing the Laptop NIC Configuration Recommendations with LaptopsMultiple Camera Issues Ethernet Switch IssuesProblems with Disconnecting NICs No camera exposure when expected Camera Exposure IssuesVPN Driver Interference Verifying Network ParametersTroubleshooting Genie Monochrome Series-GigE Vision Camera Genie Sales Information Dalsa Contact InformationInternational/Canada Genie Technical Support Glossary of Terms Acquiring an image frame SAT Glossary of Terms Genie Monochrome Series-GigE Vision Camera Genie Monochrome Series-GigE Vision Camera Index IndexIndex Genie Monochrome Series-GigE Vision Camera Genie Monochrome Series-GigE Vision Camera Index