HP Integrity Server rx4640 manual Appendix C 181

Utilities

Specifying SCSI Parameters

I/O INFORMATION

BOOTABLE DEVICES

Order Media Type Path

--------------- ---------------------------------------

1	CDROM			Acpi(HWP0002,0)/Pci(20)/Ata(Primary,Master)/CDROM(Entry0)
Seg	Bus	Dev	Fnc	Vendor	Device Slot
#	#	#	#	ID	ID	#	Path
---	---	---	---	------	------	---	-----------
00	00	01	00	0x1033	0x0035	XX	Acpi(HWP0002,0)/Pci(10)
00	00	01	01	0x1033	0x0035	XX	Acpi(HWP0002,0)/Pci(11)
00	00	01	02	0x1033	0x00E0	XX	Acpi(HWP0002,0)/Pci(12)
00	00	02	00	0x1095	0x0649	XX	Acpi(HWP0002,0)/Pci(20)
00	20	01	00	0x1000	0x0030	XX	Acpi(HWP0002,100)/Pci(10)
00	20	01	01	0x1000	0x0030	XX	Acpi(HWP0002,100)/Pci(11)
00	20	02	00	0x8086	0x1079	XX	Acpi(HWP0002,100)/Pci(20)
00	20	02	01	0x8086	0x1079	XX	Acpi(HWP0002,100)/Pci(21)
00	40	01	00	0x1000	0x0021	03	Acpi(HWP0002,200)/Pci(10)
00	60	01	00	0x1077	0x2312	02	Acpi(HWP0002,300)/Pci(10)
00	60	01	01	0x1077	0x2312	02	Acpi(HWP0002,300)/Pci(11)
00	80	01	00	0x1000	0x000F	01	Acpi(HWP0002,400)/Pci(10)
00	80	01	01	0x1000	0x000F	01	Acpi(HWP0002,400)/Pci(11)
00	C0	01	00	0x1000	0x0021	04	Acpi(HWP0002,600)/Pci(10)
00	E0	01	00	0x103C	0x1290	XX	Acpi(HWP0002,700)/Pci(10)
00	E0	01	01	0x103C	0x1048	XX	Acpi(HWP0002,700)/Pci(11)
00	E0	02	00	0x1002	0x5159	XX	Acpi(HWP0002,700)/Pci(20)

System Wake-On-LAN: Enabled

In the preceding example, a single SCSI interface is shown in the listing. The information for both channels of the SCSI interface is shown in bold, for highlighting purposes.

For each channel of the SCSI board, you need to note certain information. As an example, look at the information for the SCSI interface (the first two bold lines). For each channel of this SCSI interface, note the following information:

•Bus #—identifies the bus the device is on; for the SCSI interface, this is the same for both channels. In this example, the bus number is 20.

•Dev #—the ID the device is assigned on the bus; for the SCSI interface, this is the same for both channels. In this example, the SCSI interface is device 01.

•Fnc #—identifies the channel of the device (00 for channel A, 01 for channel B, and so on). In this example, because the SCSI interface has two channels, one channel is 00 and the other is

01.

•Vendor ID—shows the device’s vendor ID; for the SCSI interface, this is the same for both channels. For all the SCSI interface the ID is 0x1000.

•Device ID—shows the device ID; for the SCSI interface, this is the same for both channels. For the SCSI interface the ID is 0x0030.

•Slot #—identifies the physical card slot in the server where the SCSI interface is installed; for the SCSI interface, this is the same for both channels. In this example, the SCSI interface is on the I/O baseboard therefore the in slot number is xx.

•Path—identifies the device’s path; for the SCSI interface, this is the same for both channels. In this example, the SCSI interface path is Acpi(HWP0002,200)/Pci(10) for channel A and

Acpi(HWP0002,200)/Pci(11) for channel B.

Appendix C 181