HP Laser CE527A#ABA manual Repeat image, Try printing to a different output bin

Table 10-2Image defect examples (continued)

Problem	Image example			Solution
Repeat image				This type of defect might occur when using preprinted forms or a large quantity of
			Dear Mr. Abhjerhjk,	narrow paper.
			The dhjhfiuhu if teint hhkjhjnf j us a weue jd, fnk
			ksneh vnk kjdfkaakd ss hsjhnckkajhdhf kashfhnduujdn.
			Pkshkkhklhlkhkhyufwe4yrh9jjflkln djd skshkshdcnksnjcnal
			aksnclnslskjlncsl nas lnslna, ncnsljsjscljckn nsnclknsllj
			hwlsdknls nwljs nlnscl nijhsn clsncij hn. Iosi fsjs jlkh andjna this
			is a hn. jns fir stie a djakjd ajjssk. Thsi ius vnvlu tyeh lch afted,	1. Print a few more pages to see if the problem corrects itself.
			and when hghj hgjhk jdj a dt sonnleh.
			Suolklv jsdj hvjkrt ten sutc of jthjkfjkn vjdj hwjd, an olk d
			.at fhjdjht ajshef. Sewlfl nv atug ahgjfjknvr kdkjdh sj hvjk
			sjskrplo book. Camegajd sand their djnln as orged tyehha
			as as hf hv of the tinhgh in the cescmdal vlala tojk. Ho sn shj
			shjkh a sjca kvkjn? No ahdkj ahhtuah ahavjnv hv vh aefve r
			Tehreh ahkj vaknihidh was skjsaa a dhkjfn anj
			cjkhapsldnlj llhfoihrfhthej ahjkkjna oa h j a kah w asj kskjnk as
			sa fjkank cakajhjkn eanjsdn qa ejhc pjtpvjlnv4purlaxnwl. Ana	2. Make sure that the type and quality of the paper you are using meet
			l, and the askeina of ahthvnasm. Sayhvjan tjhhjhr ajn ve fh k
			v nja vkfkahjd a. Smakkljl a sehiah adheufh if you do klakc k
			w vka ah call lthe cjakha aa d a sd fijs.
			Sincerely,		HP specifications. See Paper and print media on page 73.
			Mr. Scmehnjcj
				3.	The print cartridge might need to be replaced.
				4.	Verify that the product is configured for the correct paper type.
Misformed characters				1. Print a few more pages to see if the problem corrects itself.
			AaBbCc
				2.
			AaBbCc		Make sure that the environmental specifications for the product are being met.
					See Operating environment on page 214.
		AaBbCc
		AaBbCc
		AaBbCc
		AaBbCc

Page skew

1.Print a few more pages to see if the problem corrects itself.

2.Verify that no torn pieces of paper are inside the product.

3.Make sure that paper is loaded correctly and that all adjustments have been made. See Load trays on page 81. Make sure that the guides in the tray are not too tight or too loose against the paper.

4.Turn over the paper in the tray. Also, try rotating the paper 180°.

5.Make sure that the type and quality of the paper you are using meet HP specifications. See Paper and print media on page 73.

	6.	Make sure that the environmental specifications for the product are being met.
		See Operating environment on page 214.
Curl or wave	1.	Turn over the paper in the tray. Also, try rotating the paper 180°.
	2.	Make sure that the type and quality of the paper you are using meet
		HP specifications. See Paper and print media on page 73.
	3.	Make sure that the environmental specifications for the product are being met.
		See Operating environment on page 214.
	4.	Try printing to a different output bin.
	5.	If paper is lightweight and smooth, open the CONFIGURE DEVICE menu at
		the product control panel. On the PRINT QUALITY submenu, select FUSER
		MODES, and then select the paper type you are using. Change the setting to

LOW, which helps reduce the heat in the fusing process. See Print Quality menu on page 23. You must also set the type of paper for the tray you are using. See Configure trays on page 87.

ENWW Solve print-quality problems 185