Table 2-10Jetdirect menus (continued)

Menu item

Sub-menu item

Sub-menu item

Values and Description

 

 

 

 

 

 

 

Ping Results

 

Use this item to view the ping test status and results

 

 

 

using the control panel display. You can select the

 

 

 

following items:

 

 

 

 

 

 

 

 

Packets Sent

Shows the number of packets (0 - 65535) sent to the

 

 

 

remote host since the most recent test was initiated or

 

 

 

completed.

 

 

 

 

 

 

 

 

Packets Received

Shows the number of packets (0 - 65535) received from

 

 

 

the remote host since the most recent test was initiated

 

 

 

or completed.

 

 

 

 

 

 

 

 

Percent Lost

Shows the percent of ping test packets that were sent

 

 

 

with no response from the remote host since the most

 

 

 

recent test was initiated or completed.

 

 

 

 

 

 

 

 

RTT Min

Shows the minimum detected roundtrip- time (RTT),

 

 

 

from 0 to 4096 milliseconds, for packet transmission

 

 

 

and response.

 

 

 

 

 

 

 

 

RTT Max

Shows the maximum detected roundtrip- time (RTT),

 

 

 

from 0 to 4096 milliseconds, for packet transmission

 

 

 

and response.

 

 

 

 

 

 

 

 

RTT Average

Shows the average round-trip-time (RTT), from 0 to

 

 

 

4096 milliseconds, for packet transmission and

 

 

 

response.

 

 

 

 

 

 

 

 

Ping In Progress

Shows whether a ping test is in progress. Yes indicates

 

 

 

a test in progress, and No indicates that a test

 

 

 

completed or was not run.

 

 

 

 

 

 

 

 

Refresh

When viewing the ping test results, this item updates

 

 

 

the ping test data with current results. Select Yes to

 

 

 

update the data, or No to maintain the existing data.

 

 

 

However, a refresh automatically occurs when the

 

 

 

menu times out or you manually return to the main

 

 

 

menu.

 

 

 

 

 

 

Link Speed

 

 

The link speed and communication mode of the print

 

 

 

server must match the network. The available settings

 

 

 

depend on the device and installed print server. Select

 

 

 

one of the following link configuration settings:

 

 

 

 

 

 

 

 

 

 

CAUTION If you change the link setting,

 

 

 

 

network communications with the print server

 

 

 

 

and network device might be lost.

 

 

 

 

 

 

 

 

 

Auto (default): The print server uses auto-negotiation

 

 

 

to configure itself with the highest link speed and

 

 

 

communication mode allowed. If auto-negotiation fails,

 

 

 

either 100TX HALF or 10TX HALF is set depending on

 

 

 

the detected link speed of the hub/switch port. (A

 

 

 

1000T half-duplex selection is not supported.)

 

 

 

10T Half: 10 Mbps, half-duplex operation.

 

 

 

10T Full: 10 Mbps, Full-duplex operation.

 

 

 

100TX Half: 100 Mbps, half-duplex operation.

 

 

 

100TX Full: 100 Mbps, full-duplex operation.

 

 

 

 

 

 

34 Chapter 2 Control panel

ENWW