Change Language, Statistics, Refresh Tape, Reset Drive | IBM 3590

Each AL_PA. consists of two hexadecimal numbers. After each adress is set, the device will automatically run Loop Initialization (LIP).

Change Language

Allows the operator to select the operator panel language.

Statistics

Displays the number of times certain events occurred.

Refresh Tape

This option is selectable only when a tape is loaded. It will locate to the end of the tape and rewind to its beginning.

Microcode Level

Displays the microcode EC level that is in DRAM. Figure 10 shows an example.

MICROCODE LEVEL

EC aaaaaaa

LINK bbcd_ddd

Legend Description aaaaaaa

Engineering change level

bbProduct identifier

c Link identifier d_ddd Link number

Figure 10. Microcode Level Menu

Reset Drive

Aborts the operation and causes the drive code to restart. If dump data is in the drive, it is not lost.

Note: Current operation (for example Locate) will be completed before Reset Drive runs. This may cause a delay before Reset Drive is run.

Force Error Dump

Aborts the operation, causes a recovery of the functional code, and forces a microcode dump. After getting the dump, select Reset Drive. This selection is normally used because of specific requests from support personnel.

Choosing Reset Drive or Force Error Dump causes the menu that is shown in Figure 11 on page 35 to appear.

343590 Operator Guide

Image 54

IBM 3590 manual Change Language, Statistics, Refresh Tape, Microcode Level, Reset Drive, Force Error Dump

Contents

Operator Guide Page Operator Guide Fourteenth Edition October Contents Identifying Subsystem Figures Vi 3590 Operator Guide Safety Material Handling SafetyLaser Safety and Compliance Viii 3590 Operator Guide IBM 3590 Publications PrefaceRelated Publications IBM 3490 Publications Publications RS/6000 PublicationsAS/400 Publications IBM Fibre Channel Fabric Publications IBM Ficon Publications Related Software PublicationsSA22-7456 SUN Publications Online Access IBM Storage Media supportHP Publications Other Publication Non-IBM Support Do You Have Comments or Suggestions? Xiv 3590 Operator Guide Thirteenth Edition Summary of ChangesFourteenth Edition Twelfth Edition Eighth Edition Tenth EditionNinth Edition Seventh Edition Fifth Edition Xviii 3590 Operator Guide Introduction Model Attachment It is 100MB per secondEnterprise Tape System 3590 Introduction and Planning Guide Host System Attachment A14, C10, and C14 Control Unit Operator Panel A14, C10, and C14 Operator Panel Operator Guide Drive Operator Panel and Controls Operator Panel Display Operator Guide Up Arrow ResetChange Mode Down Arrow Enter Processor Check Drive Type Indicator Options and Status Description 2x information is available in on Label Icon This section describes the indicators on Drive PowerIndicators and Icons Fiducials Processor Check Indicator Tape Position IndicatorFile Protected Icons Clean Icon Dump Icon Intervention Messages Describes messages that can be displayed for Lock magazine. See on Error Message Example FID 1 C6 Message Priority and Display Rules Message Action Term DefinitionsMessage Priorities Message Life Cycle Rules FIDRoutine Messages-Mount Routine Messages-Demount Routine Messages-Combined Demount/Mount Routine Messages-Clean Routine Messages-General Custom FID and Attn Supplemental Messages Operator Messages Feed Overcurrent Magazine Full Pinch Operator Panel Menus Tension Dropped Example of Selectable Options Operator Flow Chart Shows the operator menus with panel functions Operator Menus Options Menu Set ACF Mode Menu Set Offline Services MenuSet Online Set Address Change Language Reset DriveForce Error Dump Statistics Proceed Set Online MenuShows the Set Online menu Page Set Address Menu Confirm Offline MenuShows the Confirm Offline menu Shows the Set Address menu Causes the Set Address Menu on page 37 to appear Set Port 0 Address MenuShows the Set Port 0 Address menu Value Set Port 1 Address Menu Shows the Set Port 1 Address menu Fibre Address Menu Show Node Name Menu Port 0 Name Show Port Names MenuShows the Show Port Names menu Port 1 Name Causes the Fibre Address Menu on page 40 to appear Set Port 0 Fibre Address MenuShows the Set Port 0 Fibre Address menu Set Hard Address Set Port 1 Fibre Address Menu Shows the Set Port 1 Fibre Address menu Set Hard Address Menu Save DataSaves port Alpa and returns to Fibre Address Menu on Change Language Menu Use Soft Address MenuContinue Language Statistics Menu Shows the Statistics menuShow Statistics Show Statistics Menu Confirm Mode Change Menu Shows the Confirm Mode Change menu Automatic Cartridge Facility ACF and Magazine ACF Description ACF Functions Cartridge Storage Positions Automatic Cartridge Facility ACF and Magazine ACF Magazine Cartridge Magazine Positions Following lists the Magazine Cartridge positions Import Position Magazine WeightInserting and Removing Cartridges from the Magazine Export Position Unlocked Inserting and Removing the MagazineACF Door and Lock Function Locked Removing the Magazine from Modes of OperationInserting the Magazine Cartridge is fed to the drive loader individually each time ACF Notes Random and Random 2-LUN Manual Mode Accumulate Mode Automatic Cartridge Facility ACF and Magazine Automatic Mode System Mode 62 3590 Operator Guide Random and Random 2-LUN Modes Cell Status Indicator LEDs Cell Status Flashing Yellow-Attention indicator LED Cell Status Steady Green-In-Use Indicator LED on Cell Status Steady Green-In-Use Indicator LED Cell Status Steady Yellow-Alert Conditions Cleaning Procedures Bottom View of a Cleaning Cartridge Cleaning the Tape Path Model B11/E11Model B1A/E1A Cleaning Notification Operator Panel Cleaning NotificationScsi and Fibre Channel Interface Cleaning Notification Cleaning the Tape Cartridge Cleaning the Tape Cartridge Cleaning the Magazine 72 3590 Operator Guide FID or Attn on the Message Display Identifying Subsystem ProblemsUnable to Insert a Tape Cartridge Tape Drive is Not Ready Leader Block Detaches from the Tape Shows a cartridge with a detached leader block Unloading a Tape Cartridge after a Power Failure Scsi Bus ProblemsFibre Channel Problems Tape Winds Completely Out of the Cartridge Tape/Drive Read or Write Problems See Appendix A. Media/Hardware Problem Isolation onMessage Display is Blank ACF Recovery Procedure 78 3590 Operator Guide IBM 3590 High Performance Cartridge Tape Media Types Page Tape Handling and Storage Advantages Cartridge Capacity Capacity of a Subsystem and Cartridge Selections 84 3590 Operator Guide Cartridge Care and Handling Unpacking the CartridgesHandling the Cartridges Stacking Cartridges Cartridge Labels Damaged Cartridges Unlatched from the cartridge Cartridge Quality and Library Maintenance Tape Supplies Leader Block Replacement Illustrates the replacement procedure Replacing the Leader Block 92 3590 Operator Guide Using Non-IBM Cartridges Leader Block InspectionSee to inspect the tape in the leader block 94 3590 Operator Guide Environmental and Shipping Information Operating and Storage Environment Operating EnvironmentStorage Environment Shipping Tape Media Cartridge Cartridge Disposal EnvironmentCartridge Data Security and Cartridge Disposal Cartridge Degaussing 98 3590 Operator Guide Appendix A. Media/Hardware Problem Isolation Failure Failure Date Drive Code Unknown Other Appendix B. FID Messages FID Messages This failure may be caused by a damaged cartridge Drive Problem Call for service Drive Microcode FID FF Displayed on Drive Panel It also went to the host Appendix C. Problem Determination Scsi BusAIX Environment Attachment Check Read and Write Tests Inquiry CommandType tapeutil At the Hit any key to continue... prompt, press enter Type Wrkcfgsts *DEV *TAP ASTLVL*BASIC at the prompt AS/400 Environment Attachment CheckHP-UX Environment Attachment Check Type /opt/IBMtape/tapeutil Sun Environment Attachment Check Fibre Channel Fibre Channel Problem Determination Windows NT and Windows 2000 Environment Attachment Check 110 3590 Operator Guide Service and Media Information Messages SIMs and MIMs Appendix D. Host ReportingStatistical Analysis and Reporting System SIM/MIM Presentation CSM formally Adsm 114 3590 Operator Guide 115 116 3590 Operator Guide Trademarks Following terms are trademarks of other companies IBM Agreement for Licensed Internal Code Actions You May Not Take At the Berkeley campus AIX License Information Additional Terms and ConditionsFollowing applies Distribution Compliance Laser Safety and Compliance Communication StatementsFederal Communications Commission FCC Statement Canadian Department of Communications Compliance Statement European Union EU Electromagnetic Compatibility DirectiveGermany Electromagnetic Compatibility Directive Hinweis Statement of Limited Warranty Part 1 General Terms Warranty Period One yearIBM Warranty for Machines Extent of Warranty Items Not Covered by WarrantyWarranty Service Page Part 2 Country/region-unique Terms Production StatusLimitation of Liability EUROPE, Middle EAST, Africa Emea Following terms apply to all Emea countries Warranty Service Following terms apply to the country specifiedPage 130 3590 Operator Guide Page 132 3590 Operator Guide Glossary Capacity. See media capacity ERP. See error-recovery procedures Glossary Loader. See cartridge loader Migration. See conversion 138 3590 Operator Guide Index Numerics Library FID1 FID2 FID3 FID4 Magnetic field precaution 85 Readers’ Comments We’d Like to Hear from You How satisfied are you that the information in this book is Readers’ Comments We’d Like to Hear from You GA32-0330-13Page Part Number 19P1593 Operator Guide