Integra RDC-7.1 148, Installing the Option Boards USA and Australian Models Only

Using the RDC-7.1 with Option Boards – USA, Canada, and Australian models only –—Continued

Installing the Option Boards (USA and Australian Models Only)

The option boards should be installed in their individual designated slots. Installing the option board on a different slot may cause failure.

1 Turn off the power and unplug the power cord both from the RDC-7.1 and electrical outlet.

Be sure to turn off the power of the RDC-7.1. Inserting or removing an option board with the RDC-7.1 turned on may cause failure.

2 Take the option board out from the pack- age carefully.

The option board incorporates many components, terminals and connectors along with solderings on its surface. Touching the board with your fin- gers may cause failure or damage from static elec- tricity, incorrect contact and so on. When handling the board, be sure to hold the outer part or panel section of the board without touching the board surface.

Board

The sub-panels are fixed to the RDC-7.1 with two screws at the top and bottom, while the panel that covers slots [H] and [I] is fixed with four screws at the top and bottom. Keep the removed screws for fixing the option board.

		B
							IN	E
						D	DIGITAL
					IN		COAXIAL
					C DIGITAL
					OPTICAL
			B			1
	A				1
						2
					2
						3
					3
						4
					4
			S400			5
					5
						6
			AUDIO		6
			a			1
	The	i.LINK logo isny			1
			arks of So
	tradem		tion, registered
	Corpora and other
	in the U.S.
	countries.				2	2
						OUT
							(ASSIGNABL	E)
					L
				(SINGLE)
	L							SURR	R
			CENTER		R		SURR BAC	K R
						FER
					SUBWOO
				K
	R		SURR	SURR BACE)	PRE OU
				(ASSIGNABL
	FRONT		SUB FER
			WOO
5	Insert the option board along the rail
	softly. When the board comes to the posi-

tion where it stops but does not cover the slot completely, push the board forward a little bit more strongly.

surface

B

TuneNet-)( ETHERNET Onkyo isa “Net- Corporation trademark Tune” of .

A

		S400
	AUDIO
		a
The	i.LINK logo isny
	arks of So	ered
tradrpeomration, registhert
iCnothe U.S. and o
countries.

C

E

D	IN
	DIGITAL
IN	COAXIAL
DIGITAL
OPTICAL
1

2

B
2
3
3
4
4
is“Naett-rTaudneem”ark otiof	n.
Onkyo Corpora
5
5
6
6
ETHERNET)
(Net-Tune
1
1
2
2
OUT

(ASSIGNABL E)

3 Check the alphabet letter on the option board.

The alphabet letter is printed at the top left corner of the panel section.

B

“Net	-Tune”					B
			emark of
is a trad					n.
Onkyo		Corporatio
	ETH			ERNET
					)
		(Net-Tune

4 Remove the sub-panel with the same alphabet letter as your option board from the back of the RDC-7.1.

Use the supplied Allen wrench to loosen the screw gradually, while holding the sub-panel so that the panel will not drop down.

			L
			(SINGLE)
L							SURR	R
	CENTER		R			SURR BAC	K R
				SUBWOO		FER
R			K	PRE OU	T A
	SUB	SURR	(ASSIGNABL
FRONT		FER
	WOO

6	Fix the option board firmly to the RDC-7.1
	using the removed screws.

Be sure to tighten the screws firmly to the RDC-7.1. If the screws are loose, contact failures for ground or signal wires may occur at the section between the RDC-7.1’ s slot terminal and the option board, which may cause the RDC-7.1 or board to fail.

						IN	E
					D	DIGITAL
				C	IN	COAXIAL
					DIGITAL
					OPTICAL
			B		1
A					1
					2
					2
					3
			is“Naettr-Taudneem”ark otiof		3
				n.
			Onkyo Corpora		4
					4
			S400		5
					5
			ETHERNET)
			(Net-Tune
					6
	AUDIO				6
			a		1
The	i.LINK logo isny				1
		rks of So
trademation, registered
Corpora			and other
in the U.S.
countries.					2
					2
					OUT
						(ASSIGNABL	E)

			L
			(SINGLE)
L						SURR	R
	CENTER		R		SURR BAC	K R
				SUBWOO	FER
			K
R		SURR	SURR BACE)	PRE OU
	SUB		(ASSIGNABL
FRONT	WOO

148