Integra RDC-7.1 Specifications, Error Messages, General, Troubleshooting—Continued

Troubleshooting—Continued

Error Messages

“Not available with Headphones use”

•Operation not allowed while a pair of headphones is con- nected.

“Not available in this Sp Config”

•Doesn’t work with the current speaker configuration.

“Only available with Dolby D”

•Can be used with only Dolby Digital.

“Not available with this signal”

•Doesn’t work with the current listening mode.

“Not available with Muting”

•Operation not allowed because the RDC-7.1 is currently muted.

“Not available in this Listening Mode”

•Doesn’t work with the current listening mode.

“Not available with NET AUDIO use”

•Operation not possible with Net Audio selected for the input source.

“Not available with Dolby Headphone Off”

•Doesn’t work with the Dolby Headphone function off.

“Not available with Dolby Headphone On”

•Doesn’t work with the Dolby Headphone function on.

“Not available with zone2 out in Line out”

•Operation not possible with “1-8. f. Zone 2 Out” set to “Line Out.”

“Not available with zone3 out in Line out”

•Operation not possible with “1-8. g. Zone 3 Out” set to “Line Out.”

Memory backup

The RDC-7.1 uses a battery-less memory backup sys- tem in order to retain radio presets and other settings when it is unplugged or in the case of a power failure. Although no batteries are required, the RDC-7.1 must be plugged into an AC outlet in order to charge the backup system.

(On other than USA, Canadian, and Australian models, the RDC-7.1’s Power switch must be set to On in order to charge the backup system). Once it has been charged, the RDC-7.1 will retain the settings for several weeks, although this depends on the environment and time will be shorter in humid climates.

The RDC-7.1 contains a microcomputer for signal pro- cessing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this happens, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in again.

To reset the RDC-7.1 to its factory defaults, turn it on and, while holding down the [Video 1] button, press the [Standby/On] button. When the reset is complete, “CLEAR” appears on the display and the RDC-7.1 enters Standby mode.

Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the unit’s malfunction. Before you record important data, make sure that the material will be recorded correctly.

152

Specifications

– USA and Canadian models –

General

Power Supply Rating:		AC 120 V, 60 Hz
Consumption Power:		1.0 A
Standby Power Consumption:		3.9 W
Dimensions (W ⋅ H ⋅ D):		17 11/16" ⋅ 7 3/4" ⋅ 18 13/16"
		(450 ⋅ 197.3 ⋅ 477.1 mm)
Weight:		45.6 lbs (20.7 kg)
Inputs:
Audio
Multichannel (7.1ch) Inputs:		1 or 2 (option)
Phono (MM):		1
Line inputs:		9	(assignable)
Digital inputs Coaxial:		6
Digital inputs Optical:		6	(assignable)
Digital inputs AES/EBU		1	(option)
Video (Option)
Composite Video inputs:		6	(assignable)
S Video inputs:		6	(assignable)
Component Video RCA
inputs:		3 or 4
Component Video BNC
input:		1
Audio and Video
HDMI inputs (19-pin):		2	(option)
Miscellaneous
IR in (phoenix connector):		3	(for Main, Zone 2 and Zone 3)
Outputs:
Audio
Balanced Pre out A:		Front L/R, Center, Surround L/R,
		Surround Back L/R, Subwoofer
Unbalanced Pre out A:		Front L/R, Center, Surround L/R,
		Surround Back L/R, Subwoofer
Unbalanced Pre out B:		Subwoofer
Headphones:		1
Line outputs:		5 (assignable to Recout, Zone 2 out
		and Zone 3 out)
Digital outputs Coaxial:		2 (assignable to Recout, Zone 2 out
		and Zone 3 out)
Digital outputs Optical:		2 (assignable to Recout, Zone 2 out
Video (Option)		and Zone 3 out)
Composite Video outputs:		3	(assignable to Monitor out A/B,
		Recout, Zone 2 out and Zone 3 out)
		1	(fixed, Monitor out A)
S Video outputs:		3	(assignable to Monitor out A/B
		and Recout)
		1	(fixed, Monitor out A)
Component Video RCA
outputs:		1 or 2
Component Video BNC
output:		1
Audio and Video
HDMI output (19-pin):		1
Miscellaneous
12V Trigger out (phoenix
connector):		5	(for A, B, C, D, E)
Inputs/Outputs:
Miscellaneous
i. LINK(AUDIO) (4 pin):		2
Ethernet (Net-Tune):		1	(option)
	(1/8-inch mini-jack):	1
RS232 (9 pin D-SUB
Female connector):		1
Antennas:
FM:		75 ohms unbalanced
AM:		Included loop antenna and external
		terminal
AC Inlet:		1	(IEC type)