Integra RDC-7.1 instruction manual Cassette deck or DAT deck, MD recorder or CD recorder

Connecting AV Components—Continued

Connecting a Recording Device such as MD Recorder, DAT Deck, CD Recorder or Cassette Deck

•When connecting a MD recorder, DAT deck or CD recorder to the RDC-7.1, make connections using digital or ana- log terminals. Before making connections, refer to page 30 for correct connections.

•Connect a cassette or DAT tape deck to TAPE1, and an MD or CD recorder to TAPE 2.

•When you connect a cassette deck to the RDC-7.1, be sure to use only analog audio terminals. In the initial settings, no terminal of this unit is assigned to a REC terminal of the cassette deck. To achieve the assignment, connect the REC terminal of the cassette deck to any of the AUDIO OUT 1 to 5 terminals and set the terminal to “Tape 1 Rec Out” in the Audio Output Assign sub-menu (See page 95). In addition, you can switch the input source “TAPE2” to MD or CDR. Press the [Tape 2] button on the front panel to display “TAPE 2,” then press the [Tape 2] button again and hold it for 3 seconds. This changes the display to “MD.” If you wish to change it to “CDR,” release the button once, and press and hold it again for 3 seconds. This operation enables you to operate Onkyo MD or CD recorders

with the remote controller of this unit (Please note that the connection is required).

•When connecting to other terminals, remember to configure the audio input assignment in the Audio Assign sub- menu (See page 98) and the audio output assignment in the Audio Output Assign sub-menu (See page 95).

•You can change the display name for the input source to represent the actual connected device (See page 101).

•When you want to perform analog recording of an audio signal or operate your -compatible IntegraRESEARCH

products via connections with the RDC-7.1, you have to make analog audio signal connections. Connect the audio output terminals on the source device to the AUDIO IN terminals on the RDC-7.1 using analog audio cables (RCA/phono).

Example for connecting with the TAPE 1 as input

Connections

Cassette deck or DAT deck

When connecting to other digital audio terminals or to other analog audio out- put terminals, configure the audio out- put settings accordingly using the Audio Output Assign sub-menu (See page 95).

AUDIO IN	AUDIO OUT	AUDIO OUT
DIGITAL	DIGITAL	ANALOG
OPTICAL	OPTICAL	R	L

When connecting to other audio terminals within the same terminal section, configure the audio input settings accordingly using the Audio Assign sub-menu (See page 98).

Installation and

A	B		C DIGITAL IN	D DIGITAL IN
			OPTICAL	COAXIAL
			1	1
			2	2
		“Net-Tune”	3	3
		is a trademark of
		Onkyo Corporation.

E		- CH	F	AUDIO IN	G
		MULTI	R	L	R	L
FR	FL	IN 1
			PH		4
SUB		C
					5
				GND
SR		SL	R	L
			1		6

SBR SBL

H S VIDEO VIDEO

IN IN

1

2

3

I	COMPONENT	J		K
	VIDEO
IN 1	IN 2	COMPONENT VIDEO		ANTENNA
		(HD/BNC)	IN
	Y		Y
	PB
			PB
	PR			FM
OUT 1	IN 3			75

PR

L

HDMI	RS232
IN 1
REMOTE	12V
HDMI, the HDMI logo CONTROL
is a trademark	TRIGGER
or registered	OUT
trademarks of HDMI	A
Licensing LLC.
	200mA MAX.

ETHERNET		4	4
		5
			5
	(Net -Tune)	6	6

27

38

1 9

4

5

6

Y

OUT

PB

Y

PR

AM

IN 2	B 100mA MAX.
	C
	100mA MAX.

D100mA MAX.

E

100mA MAX.

MAIN

1	1
2	2
	OUT

2 4

DIGITAL IN

( BALANCED )
AES/EBU	3		5
	R	L	OUT R	L

1

2

OUT

S VIDEO VIDEO

PB

3

PR

4

OUT

VIDEO S VIDEO

ZONE 2
ZONE 3	UPP
OUT
IN	OUT
	IR
AC INLET

(ASSIGNABLE)(ASSIGNABLE)

(SINGLE)

When connecting to other digital audio terminals or to other analog audio out-

put terminals, configure the audio out-	AUDIO IN	AUDIO OUT	R L
			AUDIO OUT
put settings accordingly using the	DIGITAL	DIGITAL
			ANALOG
Audio Output Assign sub-menu (See	OPTICAL	COAXIAL

MD recorder or CD recorder

Example for connecting to the TAPE 2 as input

When connecting to other audio terminals within the same terminal section, configure the audio input settings accordingly using the Audio Assign sub-menu (See page 98).

39