Speaker/Output Setup—Continued

Distance Between Surr Back A SP/

Distance Between Surr Back B SP

This setting is allowed only when “Main 2ch” is selected from the Speaker Configuration sub-menu. Place two surround back speakers as close together as possible, measure the distance, and set the value (see the figure). The maximum effects will be realized by THX’s ASA* technology.

0-1 ft (0-0.3 m)(Default): This is the setting when the distance between the speakers is 0-1 foot (0-30 cm).

1-4 ft (0.3-1.2 m): This is the setting when the distance between speakers is 1-4 feet (30 cm-1.2 m).

>4 ft (1.2 m): This is the setting when the distance between speakers is 4 feet (1.2 m) or more. *ASA: Advanced Speaker Array

Audio Output Assign Sub-menu

This setting allocates audio output jacks on the RDC-7.1 to input (play) sources. The setting varies depending on the connection conditions.

The RDC-7.1 is equipped with analog output jacks for five lines, and digital output jacks: optical jacks (OPT) for two lines, and coaxial jacks (COAX) for two lines. If setting the analog jacks to “Zone 2 Out” or “Zone 3 Out,” you can also specify whether output should be variable or fixed.

The default settings are as follows:

Terminals

Default input settings

 

 

Analog 1 (AUDIO OUT 1)

Video 1 Rec Out

 

 

Analog 2 (AUDIO OUT 2)

Video 2 Rec Out

 

 

Analog 3 (AUDIO OUT 3)

Video 3 Rec Out

 

 

Analog 4 (AUDIO OUT 4)

Zone 2 Out

 

 

Analog 5 (AUDIO OUT 5)

Zone 3 Out

 

 

Opt 1 Out (DIGITAL OUT OPTICAL 1)

Tape 1 Rec Out

 

 

Opt 2 Out (DIGITAL OUT OPTICAL 2)

Tape 2 Rec Out

 

 

Coax 1 Out (DIGITAL OUT COAXIAL 1)

Video 1 Rec Out

 

 

Coax 2 Out (DIGITAL OUT COAXIAL 2)

Zone 2 Out

 

 

Analog 1-5

Set the analog audio output jacks of “AUDIO OUT 1-5.” You can select from Tape 1 Rec Out, Tape 2 Rec Out, Video 1 Rec Out, Video 2 Rec Out, Video 3 Rec Out, Zone 2 Out, Zone 3 Out, and Not Used.

 

AUDIO

1

 

2

4

3

5

RL OUT RL

Example 1:

When input (REC) of an audio recording device (e.g., a cassette deck) with TAPE 1 as an input source is connected to AUDIO OUT 1, set “Analog 1” to “Tape 1 Rec Out.”

Example 2:

When sound input of a picture recording device (e.g., a VCR) with VIDEO 1 as an input source is connected to AUDIO OUT 2, set “Analog 2” to “Video 1 Rec Out.”

Example 3:

When the amplifier for Zone 2 is connected to AUDIO OUT 5, set “Analog 5” to “Zone 2 Out.”

When nothing is connected: Select “Not Used.”

Zone 2 Out, Zone 3 Out

This item is displayed when “Zone 2 Out” or “Zone 3 Out” is specified for Analog 1-5 above. The default setting for “Zone 2 Out” is “Pre Out (variable)” and for “Zone 3 Out” is “Line Out (fixed).”

Pre Out (variable): Select this when you want to set “variable” for output to a device connected to Zone 2 or Zone 3. You should operate the RDC-7.1 to adjust the sound volume from the device in Zone 2 or Zone 3. Line Out (fixed): Select this when you want to set “fixed” for output to a device connected to Zone 2 or Zone 3. You should operate the amplifier connected to the terminal to adjust the sound volume from the device in Zone 2 or Zone 3.

Setup Menu

95

Page 95
Image 95
Integra RDC-7.1 instruction manual Audio Output Assign Sub-menu, Analog, Example, When nothing is connected Select Not Used