Integra RDC-7.1 instruction manual Preference, 120

Preference

This menu allows you to configure the listening mode settings including audio effects and playback options.

Volume Setup Sub-menu

a. Volume Display

You can switch the volume indication between an absolute value and a relative value.

Absolute (absolute value): Displayed in a range from 0

to 100.

Relative (relative value) (Default): Displayed in a range of –∞dB, –81.5 dB, –80 dB......18.0 dB. An

absolute volume value of 82 is equivalent to a relative volume value of 0 dB.

b. Muting Level

You can adjust the volume level of muted sounds. Specify at 10 dB intervals in a range from – ∞ dB and –50 dB to –10 dB. The default is “– ∞.” This option can be set for Main B and Zone 2 as well as for Main A.

c. Maximum Volume

You can set the maximum output volume level to prevent sounds from becoming too loud. When displaying in absolute values, specify at 0.5 intervals in a range from 50.0 to 99.5. When displaying in relative values, specify at 0.5 dB intervals in a range from –32 dB to +17.5 dB. If you do not want to set any specific value, leave this item “Off,” the default setting. This option can be set for Main B and Zone 2 as well as for Main A.

d. Power On Volume

You can set a constant volume level of sounds output when the RDC-7.1 is powered on. When displaying in absolute values, specify at 0.5 intervals in a range from 0 to 100. When displaying in relative values, specify at

0.5dB intervals in a range from – ∞ dB and –81.5 dB to +18.0 dB (Max). If you want to maintain a selected volume level setting when putting the apparatus into standby status, select “Last.” This option can be set for Main B and Zone 2 as well as for Main A.

Headphone Level Setup Sub-menu

a. Headphone Level

When the volume level differs between speakers and headphones, you can, in advance, fine tune the headphones volume. Adjust at 0.5 dB intervals in a range from –12 dB to +12 dB.

OSD Setup Sub-menu

This sub-menu appears when the video terminal board [H] and [I] is inserted.

a. Component Video

Specify whether or not to display the On Screen Display (OSD) on the screen, when both of the source device and TV/projector are connected to the component video terminals. This option can be set for both Main A and Main B.

OSD On (Default): OSD is displayed.

OSD Off: OSD is not displayed.

b. Immediate Display

Specify whether or not to display the description of operations on the screen while you are operating the RDC-7.1 (when the component video signal is output, nothing is displayed if set to On). This option can be set for Main B and Zone 2 as well as for Main A.

On (Default): Displayed.

Off: Not displayed.

c. Display Position

Specify the position where the Immediate Display should be displayed. You can set in a range of ten positions from Top to Bottom of the screen. By default, it is displayed at the Bottom of the screen. This option can be set for Main B and Zone 2 as well as for Main A.

d. Scan Mode

Specify whether or not to output the video signal with interlace mode.

Interlaced: Outputs with interlace mode.

NonInterlaced: Does not output with interlace mode.

e. Net-Tune OSD Display

This item appears when the ETHERNET terminal board [B] (for Net Audio) is inserted.

Specify whether or not to display a description of operations on the screen when using Net-Tune (when the component video signal is output, nothing is displayed if set to On). This option can be set for Main B and Zone 2 as well as for Main A.

On (Default): Displayed.

Off: Not displayed.

OSD Position Sub-menu

This sub-menu allows you to adjust the position of the OSD Setup Menu as it is displayed on your screen. This sub-menu appears when the video terminal board [H] and [I] is inserted. Depending on the monitor used, there may be cases where the OSD Setup Menu is not displayed in the center and parts of the menus are cut off. To adjust the position of the OSD Setup Menu, simply press the cursor buttons to inch the menu to the position you desire. This option can be set for Main B and Zone 2 as well as for Main A.

120