Integra RDC-7.1 What is i.LINK AUDIO, Copyright Protection System, Video Out

Connecting AV Components—Continued

Connection Using the i.LINK (AUDIO) Terminal ( ) (Other than Chinese model)

What is i.LINK

i.LINK is an appellation of IEEE1394, which is the digital interface standard defined by the Institute of Electrical and Electronics Engineers (IEEE).

Connecting i.LINK (AUDIO)-supported devices allows high speed transfer of data such as digital sound between the linked devices, and their control.

What is i.LINK (AUDIO)

The RDC-7.1 supports “i.LINK (AUDIO)” of the i.LINK transfer format. Accordingly, “i.LINK (AUDIO)” must also be supported for other devices that you want to connect to the RDC-7.1. The RDC-7.1 does not support other i.LINK transfer formats such as “MPEG-2 TS” used for BS digital broadcasts or “DV” used for DVD recorders, digital video, etc. The RDC-7.1 connected to other i.LINK(AUDIO)-supported devices via i.LINK cable enables you to transfer multichannel digital sound such as DVD-Audio and SACD (video signal is not supported).

Even when multiple devices are connected to each other, you can perform data transfer and control of target devices via another device.

The IEEE interfaces on the RDC-7.1 are designed conforming to the standards below.

1.IEEE Std 1394a-2000, Standard for a High Performance Serial Bus

2.IEC60958 bitstream, DVD-Audio, and SACD in the AM824 Sequence adaptation layers of Audio and Music Data Transmission Protocol 2.0

Copyright Protection System

The RDC-7.1 supports the DTCP (Digital Transmission Contents Protection) system. The DTCP system uses technol- ogies for data encryption and authentication during the data transfer between the i.LINK-connected digital devices in order to protect the copyright of the content against illegal duplication. To enjoy replaying DVD-Audio, etc., the DTCP must also be supported by other devices connected to the RDC-7.1.

How to Make a Connection through the i.LINK (AUDIO) Interface

Use the S400 4-pin i.LINK cable to connect the i.LINK (AUDIO) terminal on the RDC-7.1 to the i.LINK (AUDIO) terminal on the i.LINK (AUDIO)-enabled device.

•When using the i.LINK connection, you need to configure the audio input assignment settings in the “i.LINK” sec- tion of the Audio Assign sub-menu (Some i.LINK-connected devices may require audio output settings).

•The RDC-7.1 supports only audio signal transmission through the i.LINK (AUDIO) interface. When connecting video devices, you need to make a connection using other terminals for video signal.

VIDEO OUT

Note:

If any other IntegraRESEARCH product is connected to the RDC-7.1 via i.LINK, system operation can be achieved via i.LINK

cable. In that case, disconnect the connection as it may intro- duce errors.

In addition to the i.LINK audio connection, make sure to connect the terminals for images such as VIDEO and/or S VIDEO terminals.

A	B		C DIGITAL IN
			OPTICAL
			1
			2
		“Net -Tune”	3
		is a trademark of
		Onkyo Corporation.

D DIGITAL IN	E	MULTI	F	AUDIO IN	G		H S VIDEO	VIDEO
		- CH
COAXIAL	FR	FL IN 1	R	L	R	L	IN	IN
1			PH		4		1
	SUB	C
2					5		2
				GND
	SR	SL	R	L
3			1		6		3
	SBR	SBL

I	COMPONENT	J	K	L
	VIDEO
IN 1	IN 2	COMPONENT VIDEO		ANTENNA
		(HD/BNC)	IN
	Y		Y
	PB
			PB
	PR			HDMI
			FM	is a tr
				or reg
OUT 1	IN 3		75	trade
				Licen

PR

4

ETHERNET 5

(Net-Tune)

6

4	2	7	4
5	3	8	5
6	1	9	6

Y

OUT

PB

Y

PR

AM

1

1 2 4 1

DIGITAL IN

PB

3

40