Integra Operating with the Remote Controller, Operating on the RDC-7.1, Select a source, Notes

Enjoying Movies and Music in the Remote Zone (Zone 2/3)—Continued

Operating with the Remote Controller

When operating with the remote controller, how to operate depends on the location of Zone 2 or Zone 3, or the distance from the RDC-7.1.

•Point the remote controller at the infrared receiver on the RDC-7.1, and then operate the controller.

•Install a remote controller sensor in Zone 2 or Zone 3 through an IR connection (See pages 46-49).

•Switch the Transmission Signal Format to RF (Radio Frequency) (depending on the destination) (See page 141).

Operating on the RDC-7.1

Standby/On
Standby indicator	Master Volume

AV Controller RDC-7.1

On, Standby

CH Disc +/–

On	Standby	TV
		I	Input
1	2	3	+
@.-'/	ABC	DEF	TV CH
4	5	6	-
GHI	JKL	MNO
7	8	9
PQRS	TUV	WXYZ	TV VOL
+10	0	Clear
--/---		#
		Direct Tuning
Custom
			Zone 3
Macro			Zone 2
Mode			Input
Dimmer			Sleep
TV	Menu	Me
Input	Top	nu
+	erver	Audio
	S	AD
		J
CH	Enter		VOL
Disc
-		e
Prev	Exit	Guid
	R	p
CH	eturn	Setu
Display			Muting
Rec	Main A	Main B	Random
Audio	Subtitle	Angle	Last Memory
Surround	THX	All CH ST	Stereo
Repeat	A-B	Search	Memory
Pure A	Direct	DSP	DSP
Repeat	Video	Music	Photo
Test Tone	CH SEL	Level -	Level +
Playlist	Album	Artist	Genre
	Audio SEL	L Night	Re-EQ
Caps	Delete	Language	Location
	RC-554M

Zone 3

Zone 2

Level –/+

Zone 2 Off	Input source buttons and
Rec/Zone 3	indicators

1 Turn on the power supply to the RDC-7.1, and then select a source for Zone 2 or Zone 3.

For Zone 2: Press the [Zone 2] button, and then select the source with the input source buttons. The indicator above the selected input source button will light green.

For Zone 3: Press the [Rec/Zone 3] button, and then, select the source with the input source but- tons. The indicator above the selected input source button will light red.

When you press the [Zone 2] or [Rec/Zone 3] button, the [Standby] indicator on the RDC-7.1 blinks for three seconds, so perform operations while it is blinking.

1 Power on the devices in Zone 2 or Zone 3.

Press the [Zone 2] or [Zone 3] button, and then the [On] button.

2 Select a source.

Rotate the scroll wheel to select a source while the [Zone 2] or [Zone 3] button is lighted (if the button is not lighted, press the [Zone 2] or [Zone 3] button to light it).

•When you have selected the tuner, you can choose a preset channel with the [CH Disc +/–] button.

3 Adjust the volume level.

Press the [Zone 2] (or [Zone 3]) button, and within 5 seconds, press the [Level –/+] button to adjust the volume level.

Notes:

•When the pre-main amplifier or receiver is connected, the volume level should be adjusted at the connected component side.

•When not using Zone 2 or Zone 3, press the [Zone 2] (or [Zone 3]) button, and then press the [Standby] button.

When the same input source is selected for Zone 2 and Zone 3, it will light orange.

To switch the source for Zone 2 (or Zone 3) and the main room simultaneously:

Repeatedly press the [Zone 2] (or [Rec/Zone 3]) button to display “Z2Sel:SOURCE,” and then select the source.

2 Adjust the volume level.

For Zone 2: Press the [Zone 2] button, and then adjust with the [Master Volume] dial.

For Zone 3: Press the [Rec/Zone 3] button, and then adjust with the [Master Volume] dial.

Notes:

•When a pre-main amplifier or receiver is con- nected to the RDC-7.1, the volume level should be adjusted at the connected component side.

70