INPUT/OUTPUT/SOLO

Ch1–6: Select inputs for mixer channels 1–6

Here you can select the inputs for mixer channels 1–6. For details on connecting each input jack, refer to p.14.

4

2

3

1

1. Ch1...6 .............................................................[Input1....4, S/PDIF L, R, RhythmL, R, CD L, R*]

Select a “Ch1”–“Ch6” channel icon, and select the source that will be input to each channel. INPUT1...4: Input the analog audio signal from an instrument etc. connected to the [INPUT 1/GUITAR IN]–[INPUT 4] jacks.

S/P DIF L, R: Input the digital audio signal from a CD or DAT etc. connected to the [S/P DIF IN] jack. This can be selected if “DigiIn” is “On.”

Insert effects cannot be used when using digital in- put.

RhythmL, R: Input the rhythm selected by “SelRhythm” (→ p.96). The rhythm will sound during recording and playback, regardless of the “Rhythm” setting (→ p.96). This rhythm can be recorded (→ p.48).

CD L, R: Input the audio signal from an audio CD inserted in the CDRW-1.

*CD L, R can be selected only if the CDRW-1 is installed.

2. DigiIn ..................................................

[On, Off]

Turn this “On” when you want to use digital input (S/P DIF IN).

On: You will be able to select “S/P DIF L” or “S/ P DIF R” for “Ch1...6.”

Insert effects cannot be used if this is “On.”

Off: You will not be able to select “S/P DIF L” or “S/P DIF R” for “Ch1...6.”

Turn this “On” if you want to use digital input (S/P DIF IN). When you press the “DigiIn” button, a message of “Obey Copyright Rules” will appear. Carefully read the section “COPYRIGHT WARNING” (→ p.1), and if you accept the terms, press the [YES/OK] key in response to “Are You Sure?” Digital input will be enabled.

3. SubIn................................................................

3a

3b

3c

3d

These settings let you use the [INPUT 1/GUITAR IN]– [INPUT 4] jacks as “sub inputs,” for example when you want to use these jacks as the returns from an external effect device, or when you want the sound of instruments connected to these jacks to be combined with the track playback. (→ p.67)

Sub input can be used when you want to synchronize an external sequencer with a completed song on the D1200, and mix the instrumental sounds played by the sequencer with the playback tracks of the D1200. These inputs will be sent through the stereo/mono switch, balance, and fader to the master LR bus.

Use the [AUX OUT] jack to output the send signal to the external effect device. (→ p.90: [MASTER EFFECT/ AUX] “AuxSend” tab page)

3a. Stereo/Mono ........................

[Stereo, Mono]

Stereo: The odd-numbered channel input will be sent to the master L bus, and the even-numbered channel input will be sent to the master R bus.

Mono: The odd-numbered and even-numbered inputs will be combined, and the same signal will be sent to the master L and R buses. Use this setting if the input signal consists of only one channel.

If the sound is distorted when you use the “Mono” setting, adjust the level on the output device or using the [TRIM] knob.

3b. Balance .............................

[L63...CNT...R63]

Specifies the balance at which the sub input will be sent to the master LR bus in stereo.

3c. Fader .........................................

[000...100]

Specifies the level at which the sub input will be sent to the master LR bus.

3d. Mute..............................................[On, Off]

On: The sub input will be muted; it will not be sent to the master LR bus.

Off: The sub input will not be muted; it will be sent to the master LR bus.

4. Pair ..................................................................

Specify pairing for adjacent mixer channels.

Press the “ ” button, and make settings. (→ p.38, 86)

Ch7–12: Select inputs for mixer channels 7–12

Here you can select the inputs for mixer channels 7–12. Refer to “Ch1–6: Select inputs for mixer channels 1–6.”

98