Operation

When the operation has been completed, the display will indicate “Completed.” Press the [YES/OK] key.

5Check the results of the operation.

Press the [IN/LOC1] key, and play back from the IN location to verify that the operation did what you expected.

If you are not satisfied with the results, you can use Undo to return to the previous state. (→ p.126)

Optimize a track: “OptimizeTrack”

This command removes noise and optimizes the recorded track data in the specified region (IN–OUT).

Optimizing track data

Here’s how to optimize the IN–OUT region of track 1 so that “DiskBusy” warnings will no longer appear.

Reverse a track: “ReverseTrack”

This command copies the data in the specified region (IN– OUT) of the track “in reverse” (i.e., so that the data will play backward) and places it at the TO location, either in the same track or in another track.

•The data of the IN–OUT region can be copied one or more times in succession by a single operation.

•You can copy just one track, or multiple tracks of data at the same time.

Copying track data in reverse

Here’s how the IN–OUT region of track 1 can be copied in reverse three times starting at the TO location of track 2.

DestTrack

1Register the IN and OUT locations.

Set the IN point slightly ahead of where “DiskBusy” warnings start being displayed, and set the OUT point

to a location where these warnings are no longer dis- played. (→ p.33, 118)

2Select “Optimize.”

In the [TRACK] “EditTrk” tab page, set “EditType” to “OptimizeTrack.”

3Select the optimize mode.

Select the “Mode” button and press the [ENTER] key to open the dialog box.

SourceTrack

DestTrack

Times

1 Register the IN, OUT, and TO locations. (→ p.33, 118)

2Select “ReverseTrack.”

In the [TRACK] “EditTrk tab page, select “EditType” and use the [VALUE] dial to choose “ReverseTrack.”

3Select the reverse-source track number. Use “SourceTrack” to select track “1.”

4Select the reverse-destination track number. Use “DestTrack” to select track “2.”

If you selected two or more tracks for “SourceTrack,” you must specify the same number of tracks for “Dest- Track.”

5Specify the number of times that the data will be copied. Set “Times” to “3.”

6Select the “Exec.” button and press the [ENTER] key. When the display asks “AreYouSure?,” press the [YES/ OK] key to execute the operation.

When the operation has been completed, the display will indicate “Completed.” Press the [YES/OK] key.

7Check the results of the editing operation.

Press the [TO/LOC3] key, and play back from the TO location to verify that the operation produced the results you expect.

If you are not satisfied with the results, you can use Undo to return to the previous state. (→ p.126)

As the specified region (IN–OUT) is set longer, it will correspondingly take longer for processing to be finished and for the “Completed” indication to appear..

For this example, select “Normal” and press the [YES/ OK] key to return to the [TRACK] “EditTrk” tab page.

4Select the number of the track that you want to opti- mize.

Find the track whose data you suspect to be fragmented (here we will assume it is track 1), and set “DestTrack” to that track number (“1” in this example).

5Select the “Exec.” button and press the [ENTER] key. When the display asks “AreYouSure?,” press the [YES/ OK] key to execute the operation.

When the operation has been completed, the display will indicate “Completed.” Press the [YES/OK] key.

6Check the results of the operation.

Press the [IN/LOC1] key, and play back from the IN location. If “Disk Busy” warnings are no longer dis- played, and the data plays correctly, the data has been optimized successfully.

If you are not satisfied with the results, you can use Undo to return to the previous state. (→ p.126)

As the specified region (IN–OUT) is set longer, it will correspondingly take longer for processing to be finished and for the “Completed” indication to appear.

59