Operation

Select the “Mode” button and press the [ENTER] key to open the dialog box.

For this example, select curve “A” and press the [YES/ OK] key to return to the [TRACK] “EditTrk” tab page.

5Select the “Exec.” button and press the [ENTER] key. When the display asks “AreYouSure?,” press the [YES/ OK] key to execute the operation.

When the operation has been completed, the display will indicate “Completed.” Press the [YES/OK] key.

6Check the results of the operation.

Press the [IN/LOC1] key and play back from the IN location to verify that the fade-in was created as you expect.

If you are not satisfied with the results, you can use Undo to return to the previous state. (→ p.126)

As the specified region (IN–OUT) is set longer, it will correspondingly take longer for processing to be finished and for the “Completed” indication to appear.

Fading-out

Here’s how to fade-out the IN–OUT region of track 1.

1Register the IN and OUT locations.

Register the locations at which you want the fade-out to start and end. (→ p.33, 118)

2Select “FadeTrack.”

In the [TRACK] “EditTrk” tab page, select “EditType” and use the [VALUE] dial to choose “FadeTrack.”

3Select the fade-out curve. A., B., C.: fade-in curves D., E., F.: fade-out curves

Select the “Mode” button and press the [ENTER] key to open the dialog box. For example, select curve “D” and press the [YES/OK] key to return to the [TRACK] “Edit- Trk” tab page.

If you selected two or more tracks for “SourceTrack,” you must specify the same number of tracks for “Dest- Track.”

4Select the fade-out destination track number. Set “DestTrack” to track “1.”

5Select the “Exec.” button and press the [ENTER] key. When the display asks “AreYouSure?,” press the [YES/ OK] key to execute the operation.

When the operation has been completed, the display will indicate “Completed.” Press the [YES/OK] key.

6Check the results of the operation.

Press the [IN/LOC1] key and play back from the TO location to verify that the fade-out was created as you expect.

If you are not satisfied with the results, you can use Undo to return to the previous state. (→ p.126)

As the specified region (IN–OUT) is set longer, it will correspondingly take longer for processing to be finished and for the “Completed” indication to appear..

Normalize the level: “NormalizeTrack”

In cases where the recorded level is low, this command can boost the specified region (IN–OUT) of recorded track data to the maximum volume that will not cause clipping.

•This command searches for the peak value of the audio data within the IN–OUT region, and boosts the overall level of all the audio data in the IN–OUT region so that the peak value reaches the maximum level.

•You can normalize the data of one or more adjacent tracks simultaneously.

If you normalize data that was recorded at an extremely low level, any noise included in that region will also be boosted.

Normalizing the level

Here’s how to normalize the IN–OUT region of track 1.

DestTrack

1Register the IN and OUT locations.

Register the locations at which you want normalization to start and end. (→ p.33, 118)

2Select “NormalizeTrack.”

In the [TRACK] “EditTrk” tab page, select “EditType” and use the [VALUE] dial to choose “NormalizeTrack.”

3Select the number of the track that will be normalized. Set “DestTrack” to track “1.”

4Select the “Exec.” button and press the [ENTER] key. When the display asks “AreYouSure?,” press the [YES/ OK] key to execute the operation.

When the operation has been completed, the display will indicate “Completed.” Press the [YES/OK] key.

5Check the results of the operation.

Press the [IN/LOC1] key and play back from the IN location to verify that the data was normalized as you expect.

If you are not satisfied with the results, you can use Undo to return to the previous state. (→ p.126)

As the specified region (IN–OUT) is set longer, it will correspondingly take longer for processing to be finished and for the “Completed” indication to appear.

63