Korg D1200 9:DL2: St/Cross Delay (Stereo/Cross Delay), 10:DL3: St.Multitap Delay (Stereo Multitap Delay), 11: DL4: St.Modulation Delay

Korg D1200 9:DL2: St/Cross Delay (Stereo/Cross Delay), 10:DL3: St.Multitap Delay (Stereo Multitap Delay), 11: DL4: St.Modulation Delay

Fdback (Feedback (C Delay)) .....		–100...		+100	Sets the feedback amountof TapC
HiDamp (High Damp [%]) ...................			0...	100	Sets the damping amount in the high
					range
LoDamp (Low Damp [%])....................			0...	100	Sets the damping amount in the low
					range
Spread (Spread)	...................................			0...50	Sets the width of the stereo image of the
					effect sound
Mix (Wet/Dry) .................	Dry, 1:99...		99:1, Wet		Sets the balance between the effect and
					dry sounds

: High Damp [%], : Low Damp [%]

These parameters set the damping amount of high range and low range. The tone of the delayed sound becomes darker and lighter as it feeds back.

: Spread

This parameter sets the pan width of the effect sound. The stereo image is widest with a value of “50,” and the effect sound of both channels is output from the center with a value of “0.”

9:DL2: St/Cross Delay (Stereo/Cross Delay)

This is a stereo delay, and can by used as a cross-feedback delay effect in which the delay sounds cross over between the left and right by changing the feedback routing.

Mode (Stereo/Cross)................		Stereo, Cross			Switches between stereo delay and
					cross-feedback delay
LTime (L Delay Time [msec]) .........		0...	680ms		Sets the delay time for the left channel
RTime (R Delay Time [msec]) ........		0...	680ms		Sets the delay time for the right channel
LFback (L Feedback) ..................		–100...		+100	Sets the feedback amount for the left
					channel
RFback (R Feedback) .................		–100...		+100	Sets the feedback amount for the right
					channel
HiDamp (High Damp [%]) ...................			0	...100	Sets the damping amount in the high
					range
LoDamp (Low Damp [%])....................			0	...100	Sets the damping amount in the low
					range
Spread (Spread) .............................		–50...		+50	Sets the width of the stereo image of the
					effect sound
Mix (Wet/Dry) .................	Dry, 1:99...99:1, Wet				Sets the balance between the effect and
					dry sounds

10:DL3: St.Multitap Delay (Stereo Multitap Delay)

The left and right Multitap Delays have two taps respectively. Changing the routing of feedback and tap output allows you to create various patterns of complex effect sounds.

Mode (Mode)......................		Normal, X.Fback,			Switches the left and right delay routing
		X.Pan1, X.Pan2
T1Time (Tap1 Time [msec])		........... 0...	680ms		Sets the Tap1 delay time
T2Time (Tap2 Time [msec])		........... 0...	680ms		Sets the Tap2 delay time
T1Lvl (Tap1 Level)...............................			0	...100	Sets the Tap1 output level
Fdback (Feedback) .....................		–100...		+100	Sets the Tap2 feedback amount
HiDamp (High Damp [%]) ...................			0	...100	Sets the damping amount in the high
					range
LoDamp (Low Damp [%])....................			0	...100	Sets the damping amount in the low
					range
Spread (Spread) .........................		–100...		+100	Sets the width of the stereo image of the
					effect sound
Mix (Wet/Dry) .................	Dry, 1:99...99:1, Wet				Sets the balance between the effect and
					dry sounds

: Mode

The left/right panning of the delay can be modiﬁed by changing the connections of the left and right delay. Be aware that different sounds must be input to the left and right channels in order for this parameter to be effective.

: Tap1 Level

This parameter sets the output level of Tap1. Setting a different level from Tap2 will add a unique touch to a monotonous delay and feed- back.

11: DL4: St.Modulation Delay

(Stereo Modulation Delay)

This stereo delay uses an LFO to sweep the delay time. The pitch also varies. You will obtain a delay sound with swell and shimmering.

LFO (LFO Waveform) .......................		TRI, SIN		Selects LFO Waveform
Shape (LFO Shape) ....................		–100...	+100	Determines how much the LFO wave-
				form is changed
*Speed (LFO Frequency [Hz])....		0.02...20.0Hz		Sets the LFO speed
LPhase (L LFO Phase [degree]) .–180...			+180	Sets the phase obtained when the left
				LFO is reset
RPhase(R LFO Phase [degree]) .–180...			+180	Sets the phase obtained when the right
				LFO is reset
*LDepth (L Depth) .................................		0...	200	Sets the depth of the left LFO modula-
				tion
*RDepth (R Depth)................................		0...	200	Sets the depth of the right LFO modula-
				tion
LTime (L Delay Time [msec])...............		0...	500	Sets the delay time for the left channel
RTime (R Delay Time [msec]) .............		0...	500	Sets the delay time for the right channel
LFback (L Feedback)...................		–100...	+100	Sets the feedback amount of left delay
RFback (R Feedback) .................		–100...	+100	Sets the feedback amount of right delay
Mix (Wet/Dry) ....................	–Wet...–1:99, Dry,			Sets the balance between the effect and
		1:99...	Wet	dry sounds

: L LFO Phase [degree], : R LFO Phase [degree]

“L LFO Phase” and “R LFO Phase” specify the phase difference between the two LFO’s when they are reset. This allows the pitch change of the sweep to be set independently for left and right.

12:DL5: St.Dynamic Delay (Stereo Dynamic Delay)

This stereo delay controls the level of delay according to the input signal level. You can use this as a ducking delay that applies delay to the sound only when you input signals at a high velocity or only when the volume level is low.

Contrl (Control Target)	.............	None, Out, FB			Selects from no control, output, and
					feedback
Polrty (Polarity) .........................................				+, –	Reverses level control
Thrshl (Threshold) ...............................			0...	100	Sets the level to which the effect is
					applied
Offset (Offset)......................................			0...	100	Sets the offset of level control
Attack (Attack) .....................................			1...	100	Sets the attack time of level control
Relse (Release)...................................			1...	100	Sets the release time of level control
LTime (L Delay Time [msec])..........		0...	680ms		Sets the delay time for the left channel
RTime (R Delay Time [msec]) ........		0...	680ms		Sets the delay time for the right channel
Fdback (Feedback)......................		–100...		+100	Sets the feedback amount
HiDamp (High Damp [%])....................			0...	100	Sets the damping amount in the high
					range
LoDamp (Low Damp [%]) ....................			0...	100	Sets the damping amount in the low
					range
Spread (Spread)..........................		–100...		+100	Sets the width of the stereo image of the
					effect sound
Mix (Wet/Dry) ................	Dry, 1:99...99:1, Wet				Sets the balance between the effect and
					dry sounds

: Control Target

This parameter selects no level control, delay output control (effect balance), or feedback amount control.

: Polarity, :Threshold, :Offset, :Attack, :Release

The “Offset” parameter speciﬁes the value for the “Control Target” parameter (when level control is not being applied), expressed as a ratio relative to the parameter setting. The parameter setting will be the “Wet/Dry” value if “Control Target”=“Out,” or the “Feedback” value if “Control Target”=“FB.”

When “Polarity” is “+”, the “Control Target” value is obtained by multiplying the parameter value by the “Offset” value (if the input level is below “Threshold”), or will equal the parameter value if the input level exceeds the threshold.

When “Polarity” is “–”, the Control Target value will equal the parameter value if the input level is below “Threshold”, or is obtained by multiplying the parameter value by the “Offset” value if the input level exceeds “Threshold.”

128