Phaser

LFO (LFO Waveform)

....................... TRI, SIN

Selects LFO Waveform

*Speed (LFO Frequency [Hz]) ....0.02...20.0Hz

Sets the LFO speed

Manual (Manual) .................................

0...

100

Sets the frequency to which the effect is

 

 

 

applied

*Depth (Depth)......................................

0...

100

Sets the depth of LFO modulation

Reso (Resonance) ......................

–100...

+100

Sets the resonance amount

Mix (Wet/Dry) .....................

–Wet...–1:99, Dry,

Sets the phaser effect balance

 

1:99...

Wet

 

 

 

 

 

Trml (Tremolo)

LFO (LFO Waveform)......................

TRI, SIN,

Selects LFO Waveform

Vintage, Up, Down

 

Shape (LFO Shape)....................

–100...+100

Determines how much the LFO wave-

 

 

form is changed

*Speed (LFO Frequency [Hz]) ....

0.02...20.0Hz

Sets the LFO speed

*Depth (Depth)......................................

0...100

Sets the depth of LFO modulation

Mt.Dly (Multitap Delay)

T1Time (Tap1 Time [msec])

........... 0...

680ms

Sets the Tap1 delay time

T2Time (Tap2 Time [msec])

........... 0...

680ms

Sets the Tap2 delay time

T1Lvl (Tap1 Level)...............................

 

0

...100

Sets the Tap1 output level

Fdback (Feedback) .....................

–100...

+100

Sets the Tap2 feedback amount

HiDamp (High Damp [%]) ...................

0...

100

Sets the damping amount in the high

 

 

 

 

 

range

Mix (Wet/Dry) .................

Dry, 1:99...99:1, Wet

Sets the effect balance of the multi-tap

 

 

 

 

 

delay

Reverb (Mono Reverb)

Time (Reverb Time [sec])...........

0.1

...10.0sec

Sets the reverberation time

HiDamp (High Damp [%]) ................

0...

100%

Sets the damping amount in the high

 

 

 

 

range

PreDly (Pre Delay [msec]) ..........

0...

200msec

Sets the delay time of the reverb sound

 

 

 

 

and gate control signal

EQTrim (EQ Trim)................................

 

0...100

Sets the EQ input level

LEQG (Pre LEQ Gain [dB]).........

–15...

+15dB

Sets the gain of Low EQ

HEQG (Pre HEQ Gain [dB])........

–15...

+15dB

Sets the gain of High EQ

RevBal (Reverb Balance)......

Dry, 1:99...

99:1,

Sets the effect balance of the reverb

 

 

 

Wet

 

Gate

Contrl (Input Reverb Mix)......

Dry, 1:99...

99:1,

Sets the balance between the dry and

 

 

Wet

reverb sounds of the gate control signal

Polrty (Polarity) ........................................

+, –

Switches between non-reversed and

 

 

 

reversed Gate on/off

Thrshl (Threshold)...............................

0...

100

Sets the level to which the Gate is

 

 

 

applied

Attack (Attack).....................................

1...

100

Sets the attack time

Relse (Release) ..................................

1...

100

Sets the release time

The Gate of 86:MM32: Reverb-Gate is connected to the Wet output of the reverb.

This means that the on/off switch of the Gate effect is linked to the Reverb, and will be switched on/off in conjunction with the Reverb.

Insert (1in1outx8)

These algorithms can be selected as an insert effect if “1in1outx8” is selected for “SelectEffType.”

Different insert effects can be used on each of eight channels/ tracks.

Effects MN1–MN11are monaural type effects.

1in1outx8” effects cannot be controlled by an expression pedal etc.

88: MN1: OverDrive/HighGain

The parameters are the same as for ODHIG.

89: MN2: Compressor2

The parameters are the same as for Comp2.

90: MN3: Limiter

The parameters are the same as for Lmtr.

91: MN4: Gate

Polrty ([G] Polarity)

...................................

+, – Switches between non-reversed and

 

 

 

reversed Gate on/off

Thrshl (Threshold) ...............................

0...

100

Sets the level to which the Gate is

 

 

 

applied

Attack ([G] Attack) ...............................

1...

100

Sets the attack time

Relse (Release)...................................

1...

100

Sets the release time

92: MN5: Exciter2

The parameters are the same as for Excit2.

93: MN6: Parametric 4band EQ

Fc1 (Band1 Cutoff [Hz])

........... 20Hz...

1.0kHz

Sets the center frequency of Band 1

Q1

(Q) .............................................

0.5...

10.0

Sets the bandwidth of Band 1

G1

(Gain [dB]) ............................

–18...

+18dB

Sets the gain of Band 1

Fc2 (Band2 Cutoff [Hz])

....... 300Hz...

10.0kHz

Sets the center frequency of Band 2

Q2

(Q) .............................................

0.5...

10.0

Sets the bandwidth of Band 2

G2

(Gain [dB]) ............................

–18...

+18dB

Sets the gain of Band 2

Fc3 (Band3 Cutoff [Hz])

....... 300Hz...

10.0kHz

Sets the center frequency of Band 3

Q3

(Q) .............................................

0.5...

10.0

Sets the bandwidth of Band 3

G3

(Gain [dB]) ............................

–18...

+18dB

Sets the gain of Band 3

Fc4 (Band4 Cutoff [Hz])

....... 500Hz...

20.0kHz

Sets the center frequency of Band 4

Q4

(Q) .............................................

0.5...

10.0

Sets the bandwidth of Band 4

G4

(Gain [dB]) ............................

–18...

+18dB

Sets the gain of Band 4

Trim (Trim) ...........................................

0...

100

Sets the parametric EQ input level

94: MN7: Amp Simulator

Type (Amplifier Type) .......................

AMP1...5 Selects the type of guitar amplifier

95: MN8: Multitap Delay

The parameters are the same as for Mt.Dly.

96: MN9: Chorus/Flanger2

The parameters are the same as for ChFl2.

97: MN10: Phaser

The parameters are the same as for Phaser.

140