Korg D1200 Category: Pre-ampsimulator, 48: PA1: Pre Amp Simulator, Drive, NR2, PA1

Effect Parameter List

PA1

Category: Pre-amp simulator

48: PA1: Pre Amp Simulator

[Drive, NR2, Tone, Cabinet]

Drive

This effect models a compact effect unit or amp head.

Type (DriveType) .........................................	*1	Drive type
Drive (DriveGain) ..................................	1-100	Depth of distortion
Level (Level)..........................................	0-100	Output level
Tube (TubeType) ....................	SS, 1-99, Burn!	Vacuum tube characteristics
Bias (TubeBias).....................................	0-100	Vacuum tube bias level

(2in2outx2)/ Effect

*1: TubeOD, Classic, FatDist,Metal, Seattle,BigFuzz,TopBst,US.HiG, B.Stack,Direct

Master/Final

EB1 – EB3

Category: Bass multi

49: EB1: Bass Multi1

[CompT, Exctr, P4EQ, Cho/Fl, S.DLY]

50: EB2: Bass Multi2

[Dist, NR, Filter, Delay]

51: EB3: Bass Multi3

[Comp, P4EQ, Gate]

*The Tube parameter lets you vary the way in which the sound is distorted by vacuum tubes. It simulates the way that distortion is influenced by the amplitude, number of vacuum tubes, and their age. As you increase the value of this param- eter, non-linear distortion will increase, and the overtone structure will change. It is best to raise the Drive value, and then adjust the Tube value.

*The Bias parameter adjusts the bias point of the vacuum tubes that distort the sound. In conjunction with the Tube parameter, this will vary the overtone structure. The Bias parameter will have a greater effect when the Tube setting is high.

NR (Noise Reduction)

This effect suppresses noise.

Insert

(2in2outx2), Final

Insert

)(1in2outx2)

MS1

Category: Mic multi

52: MS1: Mic Multi

[CabRes, MicSim, Comp]

Thrsh (Threshold) .......................	–40.0...–1.0 Sets the level at which the effect begins
	to apply

NR2 (Noise Reduction2)

This effect reduces the noise.

It is optimized specifically for use in a pre-amp chain.

Thrshl (Threshold).......................	–40.0...	–0.0	Level at which noise reduction begins to
			apply
Decay (Decay) ......................................	0	...20	Decay time

InsertI

(1in1outx4)

VO1 – VO2

Category: Vocal multi

53: VO1: Vocal Multi1

[Comp, Exctr, Pitch, S.Dly]

54: VO2: Vocal Multi2

[NR, DeEss, P4EQ, Cho/Fl, S.Dly]

Effects within multi-effect programs GT1–VO2, and their parameters

Here are explanations of the parameters of each effect in the multi-effect chains listed above.

Dist (Distortion)

This effect distorts the input sound

Type (DriveType)........	Tube, Crunch, Scream,		Selects the drive type
	HotBox, Higain, Valve,
	Crush, Scoop, Fuzz
Drive (Drive) ........................................	1...	100	Sets the degree of distortion
Treble (Treble)............................	–15.0...+15.0		Sets the high-frequency tone
Level (Level) ........................................	0...	100	Sets the output level

*Threshold must be adjusted according to the input level. Since the input level of a guitar will differ depending on whether it has single-coil or humbucking pickups, adjust the input trim to an appropriate level before you adjust Threshold. For a single-coil guitar, leave the trim set to approximately -10 at a point where the noise is not too loud, and then adjust Threshold so that the sound is not cut off unnaturally.

Since NR2 is optimized specifically for pre-amp, it operates dif- ferently than NR.

Comp (Compressor/Limiter)

Ratio (Ratio).....................	1.0:1...50.0:1, Inf:1			Sets the signal compression ratio
Thrshl (Threshold [dB]) ...................	–40...		0dB	Sets the level above which the compres-
				sor is applied
Attck (Attack).......................................		1...	100	Sets the attack time
Relse (Release) ..................................		1...	100	Sets the release time
GLevel (Gain Adjust [dB]) .......................			–Inf,	Sets the compressor output gain
	–38	...+24dB

CompT (Tube Compressor/Limiter)

This is a vacuum tube type compressor.

Ratio (Ratio).....................	1.0:1...50.0:1, Inf:1		Sets the signal compression ratio
Thrsh (Threshold[dB]) .....................	–40...	0dB	Sets the level above which the compres-
			sor is applied
Attck (Attack).......................................	1...	100	Sets the attack time
Relse (Release) ..................................	1...	100	Sets the release time
GLevel (Gain Adjust[dB]) ....	–Inf, –38...+24dB		Sets the compressor output gain
Tube (TubeType) ....................	SS, 1-99, Burn!		Vacuum tube characteristics

Insert

Insert (1in1outx8)

Effect Control

Modeling effects

135