Korg D1200 InEq1–4:Adjust the EQ for inputs 1–, Solo: Select the signal to be soloed, [100Hz, Reference, InputHigh, [On, Off], 20.0k (Hz)], 4. InputMid, 5. InputLow

Reference

InEq1–4: Adjust the EQ for inputs 1– 4

Here you can apply EQ (equalization) to the analog inputs from the [INPUT 1/GUITAR IN]–[INPUT 4] jacks. Use this when you want to record the sound with EQ applied.

The EQ is a three-band type, with shelving-type high and low bands, and a peaking-type mid band with adjustable center frequency.

The input EQ cannot be applied to the digital input (S/ P DIF IN) or to the rhythm.

The “InEq1–4” tab page settings cannot be paired.

5

1

3 4 2

1.InputLevelMeter.................................................

(1, 2, 3, 4/CLP, –8, –18, –42 dB)

Indicates the level of each analog input.

The horizontal axis indicates the channel, and the vertical axis indicates the level.

Inputs that are not selected in the [INPUT/OUTPUT/ SOLO] “Ch1...6” tab page will not be shown here.

2.	InputHigh..........	[(Fc=10kHz) –15.0...	+15.0 (dB)]
	Sets the input high EQ gain. This will adjust the high-
	frequency range.
	The region above 10 kHz can be boosted/cut over a
	range of –15.0 – +15.0 dB.
3.	InMidFc..............................	[100Hz...	20.0k (Hz)]

Specifies the frequency of the input mid EQ.

The frequency can be adjusted over a range of 100 Hz– 20.0 kHz.

4. InputMid.............................. [–15.0...+15.0 (dB)]

Sets the input mid EQ gain. This will adjust the mid-frequency range.

The region specified by InputMid can be boosted/cut over a range of –15.0 – +15.0 dB.

5. InputLow............ [(Fc=100Hz) –15.0...+15.0 (dB)]

Sets the input low EQ gain. This will adjust the low-frequency range.

The region below 100 Hz can be boosted/cut over a range of –15.0 – +15.0 dB.

Solo: Select the signal to be soloed

2

1

3

1.SelectSolo .........................................................[1...6, 7–8...11–12, S1, S2, A1, R1, R2/On, Off]

Switches the solo function on/off.

Only the audio signals for which the “Solo” button is on will be sent to the monitor LR bus. Use this when you want to hear only a specific audio channel out of many channels, or when you want to check the send signal. The solo signal will be output from the [MONITOR OUT L/R] jacks and from the [PHONES] jack.

If even one of these solo buttons is “On,” the [INPUT/ OUTPUT/SOLO] key will blink.

On: Solo will be on. Only the corresponding signal will be heard.

Off: Solo will be off. If any other signal is being soloed, the corresponding signal will be muted.

1...6: Mixer channel 1–6

7–8...11–12:Mixer channels 7–8...11–12.

S1, S2: Send to master effects 1 and 2

A1: Send to the [AUX OUT] external output jack

R1, R2: Return from master effects 1 and 2

The volume of each signal is set by the corresponding page or knob. When you select a different signal to be soloed, the monitor volume may change significantly.

2. ClearAll ............................................................

Turns “Off” all solo signals that are currently turned “On” by the “SelectSolo” buttons.

3. SoloToMstOut...................................... [On, Off]

Specifies whether the soloed signal(s) will be output from the [MASTER OUT L/R] jacks. Turn this on if your monitor system is connected to the [MASTER OUT L/R] jacks and you want to solo through those jacks. On: The solo signal(s) will be output from the [MONITOR OUT L/R] jacks.

Off: The solo signal(s) will be output from the [MONITOR OUT L/R] jacks and the [PHONES] jack.

The “On” setting is valid only while you are in the [INPUT/OUTPUT/SOLO] tab page. When you leave this page, the setting will automatically be turned “Off.”

	COUNTER
	MODELING
INSERT EFFECT
	EQ
MASTER	EFFECT/	AUX SEND
FINAL EFFECT
	BOUNCE
	CD
	TUNER
	RHYTHM
INPUT/	OUTPUT/	SOLO
SYSTEM/ USB
	TRACK
	SONG
IN/LOC1, …END/LOC4
	MARK
	SCENE
AUTO PUNCH
	LOOP
	TRIGGER
	SCRUB
METER/ TRACK VIEW
	UNDO

99