Appendix

Are you using the correct device for control?

→Use the device that is selected for “Device” in the [SYS-

TEM/USB] “Control” tab page. (→ p.101)

Have you selected effect program number “000” (=NO EFFECT), or have you selected an effect program that does not include a control function?

If you are using MIDI to control the effect, are the D1200 and the transmitting MIDI device set to the same MIDI channel? (→ p.79, 101)

Can’t select insert effect “1in2out x2”

Insert effect assign may be set to “Trk.”

→You can select “1in2out x2” if [INSERT EFFECT] “In- sAss” tab page “Assign” is set to “In.” Change the setting to “In.”

Can’t select insert effect “1in1out x8”

Insert effect assign may be set to “In.”

→You can select “1in1out x 8” if [INSERT EFFECT] “In- sAss” tab page “Assign” is set to “Trk.” Change the set- ting to “Trk.”

Can’t apply master effects

The send level from each channel may be at zero or nearly zero.

→In the [MASTER EFFECT/AUX SEND] “EffSnd1” or “EffSnd2” tab page, adjust “Send” to raise the send level.

The return level may be at zero or nearly zero.

→In the [MASTER EFFECT/AUX SEND] “MstEff1” or “MstEff2” tab page, adjust “RetLev” to raise the return level.

If you are monitoring the sound from the [MONITOR OUT L/R] jacks, the monitor LR bus output may be turned off.

→In the [INPUT/OUTPUT/SOLO] “Monitor” tab page, press the “MasterLR” button to turn it “On.”

Can’t apply the final effect

If you are monitoring the sound from the [MONITOR OUT L/R] jacks, the master LR bus output may be turned off.

→In the [INPUT/OUTPUT/SOLO] “Monitor” tab page, press the “MasterLR” button to turn it “On.”

→Press the [PLAY] key. The rhythm will sound when the recorder is recording or playing.

If you want to check the rhythm while the recorder is stopped, access the [RHYTHM] “SetUp” tab page.

You may have selected a silent rhythm pattern.

The rhythm volume may be too low.

→In the [RHYTHM] “SetUp” tab page, use “Rhythm Vol” to adjust the volume. If you are using tempo maps, use the “TmpMap” tab page “Edit” button to adjust the vol- ume of each map.

Rhythm sound does not go away, or sounds in duplicate (ex- cessive volume)

In the [RHYTHM] “SetUp” tab page, “Rhythm” may be “On” ([RHYTHM] key lit).

→Either change the “Rhythm” setting from “On” to “Off,” or use “Vol” to lower the volume.

Rhythm may be selected for monitoring.

→In the [INPUT/OUTPUT/SOLO] “Monitor” tab page, turn “Rhythm” “Off.”

Rhythm may be assigned as an input.

→In the [INPUT/OUTPUT/SOLO] “Ch1–6” or “Ch7–12” tab page, either select a channel assignment other than “Rhythm L” or “Rhythm R,” or turn “Rhythm” “Off” in the [RHYTHM] “SetUp” tab page.

A key does not function when pressed

Some keys do not function while the recorder is playing or recording.

→Stop the recorder, and then perform the operation.

Some keys do not function while Scrub is on.

→ Turn off Scrub, and then perform the operation. (→ p.34, 124)

Is a dialog box open?

→Press either the [YES/OK] key or the [NO/CANCEL] key to close the dialog box.

Troubleshooting

Rhythm Pattern List Effect Program List D1200 specifications About the CDRW-1Messages

Can’t apply external effect ([AUX OUT])

The external send level may be at zero or nearly zero.

→In the [MASTER EFFECT/AUX SEND] “AuxSend” tab page, use “AUX” to raise the external send level.

Is the output of the external effect connect to the [INPUT 1]–[INPUT 4] jacks, and assigned to a mixer input?

→Make the appropriate assignment in the [INPUT/OUT- PUT/SOLO] “Ch1–6” or “Ch7–12” tab page.

Have sub input settings been made correctly? (→ p.67, 99)

Rhythm

Rhythm sound is not output

In the [RHYTHM] “SetUp” tab page, “Rhythm” may be turned “Off.” ([RHYTHM] key dark)

→Turn “Rhythm” “On.”

The recorder may be stopped.

MIDI

MIDI sequencer won’t synchronize/MIDI control is not possible

Are the MIDI cables connected correctly? (→ p.14, 79)

A MIDI cable may be broken.

Can’t synchronize using MTC or MIDI Clock

Are the master and slave settings correct? (→ p.79)

Does the synchronization signal transmitted by the D1200 match the synchronization signal being received by your MIDI sequencer?

→ Check the “Select MIDI Sync Mode” setting. (→ p.79, 102)

If “TempoSource” is set to “TempoTrack,” has MIDI clock or tap tempo data been recorded on the tempo track? (→ p.51)

Have the appropriate synchronization settings been made on your MIDI sequencer?

→Refer to the owner’s manual of your MIDI sequencer.

Index

MIDI implementationBlock diagram chart

145