Korg D1200 Category: Modulation-typeeffects, 13: DL6: St.Auto Panning Delay, 14:MO1: St.Chorus (Stereo Chorus), 15:MO2: St.Flanger (Stereo Flanger)

Korg D1200 Category: Modulation-typeeffects, 13: DL6: St.Auto Panning Delay, 14:MO1: St.Chorus (Stereo Chorus), 15:MO2: St.Flanger (Stereo Flanger)

Effect Parameter List

The “Attack” and “Release” parameters specify attack time and release time of delay level control.

13: DL6: St.Auto Panning Delay

(Stereo Auto Panning Delay)

This stereo delay effect pans the delay sound left and right using the LFO.

LTime (L Delay Time [msec]) ..........		0	...680ms		Sets the delay time for the left channel
LFback (L Feedback)...................		–100...		+100	Sets the feedback amount for the left
					channel
RTime (R Delay Time [msec]) ........		0...	680ms		Sets the delay time for the right channel
RFback (R Feedback) .................		–100...		+100	Sets the feedback amount for the right
					channel
HiDamp (High Damp [%])....................			0...	100	Sets the damping amount in the high
					range
LoDamp (Low Damp [%]) ....................			0...	100	Sets the damping amount in the low
					range
LFO (LFO Waveform) .......................			TRI, SIN		Selects LFO Waveform
Shape (LFO Shape) ....................		–100...		+100	Determines how much the LFO wave-
					form is changed
Phase (LFO Phase [degree]) ......		–180...		+180	Sets the LFO phase difference between
					the left and right
*Speed(Panning Frequency [Hz]).....................					Sets the panning speed
		0.02...	20.0Hz
*Depth (Panning Depth) ........................			0...	100	Sets the panning width
Mix (Wet/Dry)............	Dry, 1:99...99:1, Wet				Sets the balance between the effect and
					dry sounds

Modulation MO1– MO7

Category: Modulation-type effects

14:MO1: St.Chorus (Stereo Chorus)

This effect adds thickness and warmth to the sound by modulating the delay time of the input signal. A two-band equalizer can be used to adjust the tone of the effect sound. You can control the spaciousness of the sound by offsetting the phase of the left and right LFOs from each other.

LFO (LFO Waveform) .......................	TRI, SIN			Selects LFO Waveform
Phase (LFO Phase [degree]) ......	–180...		+180	Sets the LFO phase difference between
				the left and right
*Speed (LFO Frequency [Hz])....	0.02...	20.0Hz		Sets the LFO speed
LDly (L Pre Delay [msec])...........	0.0...	50.0ms		Sets the delay time for the left channel
RDly (R Pre Delay [msec]) .........	0.0...	50.0ms		Sets the delay time for the right channel
*Depth (Depth) ......................................		0...	100	Sets the depth of LFO modulation
EQTrim (EQ Trim) ................................		0...	100	Sets the EQ input level
LEQG (Pre LEQ Gain [dB]) .......	–15.0...	+15.0		Sets the gain of Low EQ
HEQG (Pre HEQ Gain [dB]) ......	–15.0...	+15.0		Sets the gain of High EQ
Mix (Wet/Dry) ...–Wet...–1:99, Dry, 1:99...			Wet	Sets the balance between the effect and
				dry sounds

: L Pre Delay [msec], : R Pre Delay [msec]

Setting the left and right delay time individually allows you to control the stereo image.

15:MO2: St.Flanger (Stereo Flanger)

This effect gives a signiﬁcant swell and movement of pitch to the sound. It is more effective when applied to a sound with a lot of harmonics. This is a stereo ﬂanger. You can add spread to the sound by offsetting the phase of the left and right LFOs from each other.

Time (Delay Time [msec])...........	0.0...50.0ms	Sets the delay time from the original
		sound
LFO (LFO Waveform) .......................	TRI, SIN	Selects LFO Waveform
Shape (LFO Shape) ....................	–100...+100	Determines how much the LFO wave-
		form is changed

Phase (LFO Phase [degree])		...... –180...	+180	Sets the LFO phase difference between
				the left and right
*Speed (LFO Frequency [Hz])		....0.02...20.0Hz		Sets the LFO speed
*Depth (Depth)......................................		0...	100	Sets the depth of LFO modulation
Fdback (Feedback) .....................		–100...	+100	Sets the feedback amount
HiDamp (High Damp [%]) ...................		0...	100	Sets the feedback damping amount in
				the high range
Mix (Wet/Dry) .....................	–Wet...–1:99, Dry,			Sets the balance between the effect and
		1:99...	Wet	dry sounds

: LFO Shape

Changing the LFO waveform shape controls the peak sweep of ﬂanging effects.

: Feedback, : Wet/Dry

The peak shape of the positive and negative “Feedback” value is dif- ferent. The harmonics will be emphasized when the effect sound is mixed with the dry sound if you set a positive value for both “Feed- back” and “Wet/Dry”, and if you set a negative value for both “Feedback” and “Wet/Dry”.

: High Damp [%]

This parameter sets the amount of damping of the feedback in the high range. Increasing the value will cut high-range harmonics.

16:MO3: St.Phaser (Stereo Phaser)

This effect creates a swell by shifting the phase. It is very effective on electric piano sounds. This is a stereo effect, and you can control the spaciousness of the sound by offsetting the phase of the left and right LFOs from each other.

LFO (LFO Waveform).......................	TRI, SIN		Selects LFO Waveform
Shape (LFO Shape)....................	–100...	+100	Determines how much the LFO wave-
			form is changed
Phase (LFO Phase [degree]) ......	–180...	+180	Sets the LFO phase difference between
			the left and right
*Speed (LFO Frequency [Hz]) ....	0.02...20.0Hz		Sets the LFO speed
Manual (Manual) .................................	0...	100	Sets the frequency to which the effect is
			applied
*Depth (Depth)......................................	0...	100	Sets the depth of LFO modulation
Reso (Resonance) ......................	–100...	+100	Sets the resonance amount
HiDamp (High Damp [%]) ...................	0...	100	Sets the resonance damping amount in
			the high range
Mix (Wet/Dry) ... –Wet...–1:99, Dry, 1:99...		Wet	Sets the balance between the effect and
			dry sounds

: Resonance, : Wet/Dry

The peak shape of the positive and negative Feedback value is dif- ferent. The harmonics will be emphasized when the effect sound is mixed with the dry sound, if you set a positive value for both “Reso- nance” and “Wet/Dry”, and if you set a negative value for both “Resonance” and “Wet/Dry”.

: High Damp [%]

This parameter sets the amount of damping of the resonance in the high range. Increasing the value will cut high-range harmonics.

17:MO4: St.Vibrato (Stereo Vibrato)

This effect causes the pitch of the input signal to shimmer. You can use an expression pedal etc. to gradually increase or decrease the shimmering speed.

LFO (LFO Waveform)	....................... TRI, SIN	Selects LFO Waveform
Shape (LFO Shape)....................	–100...+100	Determines how much the LFO wave-
		form is changed
*Speed (LFO Frequency [Hz]) ....0.02...20.0Hz		Sets the LFO speed
*Depth (Depth)......................................	0...100	Sets the depth of LFO modulation
Mix (Wet/Dry) .................	Dry, 1:99...99:1, Wet	Sets the balance between the effect and
		dry sounds

Insert I )/(2in2outx2)/	Master/Final Effect

(2in2outx2),	Final
Insert


Insert (1in2outx2)


Insert (1in1outx4)


Insert (1in1outx8)


Effect Control


Modeling effects

129